16 E flame spray
09-09-2012, 11:04 AM,
#1
16 E flame spray
Hi
I am trying to coat steel alloys with 1%C steel and a bond coat NiAl (95/5).
Could anybody help me in using parameters to minimize porosity and best adhesion?
I am using a 15E gun which is very similar to 16E Metco with wire feed controller and 1/8" wires, Oxygen and Acetylene gases.
thanks,

Reply
09-10-2012, 04:01 AM,
#2
RE: 16 E flame spray
Does this help you any ??

(Please see attachment)


All the best

Kev


Attached Files
.pdf   16E Parameters.pdf (Size: 65.35 KB / Downloads: 1,983)
Reply
09-10-2012, 08:50 AM,
#3
RE: 16 E flame spray
Thanks Kev; but does it mean we should not change them at all and with these parameters we will get the best quality?
Regards,



(09-10-2012, 04:01 AM)KevGarty Wrote: Does this help you any ??

(Please see attachment)


All the best

Kev

Reply
09-10-2012, 09:07 AM,
#4
RE: 16 E flame spray
They are the Parameters that Metco would give as per the tech bulletins
If you get hold of that it will give you the hardness etc etc

Best thing to do is have a play with parameters see what suits you best but you would obviously need metallography equipment to find out porosity levels and the likes. Generally with wire flame you'll prob get around 10% porosity (approx)

I'll have a dig through my comp see what Ive got tomorrow (Australia time)

Any probs give me a yell

All the best

Reply
09-17-2012, 08:32 AM,
#5
RE: 16 E flame spray
This are start parameters and if necesary you can change them, in order to achieve the resoult, that becouse gases stecchiometry can change a little.
Best regards
Luigi
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Propeller shaft repair by flame spray in the cones area Iwan Sedaryawan CA 1 1,646 12-09-2016, 04:56 AM
Last Post: Stephen Booth
  Flame spray guns 5P, 5PII, Type N Hector Monjardin 1 2,189 11-17-2016, 10:35 PM
Last Post: mgbaca
  Build up with Powder Flame Spray Met.Eng. 8 8,189 05-30-2016, 12:08 PM
Last Post: Gordon
  Wire Flame spray and Twin Arc spraying wtaz 1 2,758 03-30-2015, 09:41 PM
Last Post: loriolo
  Technology of Flame Spray -old and new Boris Eizner 0 2,125 01-29-2015, 10:04 AM
Last Post: Boris Eizner
  acetylene flow limits for flame spray metco 6c chromalloymachi112 1 2,761 12-04-2014, 12:18 AM
Last Post: Met.Eng.
  "Flame Spray Handbook" sal 0 2,928 04-28-2013, 07:49 PM
Last Post: sal
  Powder Flame Spray for Ceramics Met.Eng. 9 8,530 09-19-2011, 04:46 PM
Last Post: Gordon
  Machining for Aluminum Bronze wire flame spray iwan-sedaryawan 3 6,143 01-12-2011, 11:47 AM
Last Post: iwan-sedaryawan
  Flame spray aluminuim WULF 4 4,360 02-06-2010, 10:02 AM
Last Post: WULF
  Which powder should I use with my combustion flame spray gun? jamaicanarchie 3 4,542 06-06-2009, 06:05 PM
Last Post: Gordon
  Flame Spray with Liquid Precursor aioa 4 5,455 03-27-2009, 08:46 PM
Last Post: Gordon
  Flame Spray Gun aioa 2 4,507 03-16-2009, 06:13 PM
Last Post: aioa
  Flame spray parameters TurbineRepair 11 17,141 11-18-2008, 03:01 AM
Last Post: kc77
  Copper based alloy as a bonding layer in Flame / arc spray. iwan-sedaryawan 5 8,205 08-27-2008, 03:59 AM
Last Post: iwan-sedaryawan



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd