Turbine high speed shaft RPM 6000 to be coating
10-08-2009, 05:15 AM,
#1
Turbine high speed shaft RPM 6000 to be coating
Dear all,
Does anyone has any experiences to do spraying on Turbine Shaft dia 92 x 146 mm area to be sprayed in 650 mm in total length with RPM 6000 by using conventional methode - flame combustion / Arc spray - ? please let me know the result is okay by applying this methode ? should we use HVOV or Plasma ?
The shaft is in Gear box of Lufkin Gear Box type TFWP.
Your reply is highly appreciated.
Thanks & Regards,
Iwan Sedaryawan - Website : https://www.ciptaagung.com
Happy0193
Reply
10-10-2009, 04:16 PM,
#2
RE: Turbine high speed shaft RPM 6000 to be coating
Hi iwan-sedaryawan

I'm sure of similar applications of combustion wire spray 13Cr steel and molybdenum coatings in past were ok, but no specific experience I'm afraid.
Reply
10-16-2009, 01:25 PM,
#3
RE: Turbine high speed shaft RPM 6000 to be coating
(10-08-2009, 05:15 AM)iwan-sedaryawan Wrote: Dear all,
Does anyone has any experiences to do spraying on Turbine Shaft dia 92 x 146 mm area to be sprayed in 650 mm in total length with RPM 6000 by using conventional methode - flame combustion / Arc spray - ? please let me know the result is okay by applying this methode ? should we use HVOV or Plasma ?
The shaft is in Gear box of Lufkin Gear Box type TFWP.
Your reply is highly appreciated.

Dear iwan-sedaryawan,
For gearbox (oil wetted areas) we recommend using either:
metco 63NS (below 430°c) or metco 450NS (up to 800°c)
63NS is hard with sliding properties, resistant to fretting and can be used in oxydizing conditions
450NS is resiatnt to corrosion and abrasion. used for build-up on machinable carbon steels and corrosion resistant steels.
Both are powder type.

We repair aircraft auxilliary power units that includes diameter restoration (shafts, gears) up to 60.000 RPM

Hope it helps
regards
Reply
12-08-2009, 12:15 PM,
#4
RE: Turbine high speed shaft RPM 6000 to be coating
Dear iwan-sedaryawan

If your question is still actual.
I've used combustion wire spray in high velocity mode for carbon (0.7%) steel. Only good result for brass and babbit slider bearings of turbines. I've got some troubles with 13% chromium steel after quick wear of babbit slider bearings. I have some ideas why, but not able to defend it. Anyway I would recommend carbon (0.7%) steel deposition by combustion wire spray.

Sincerely Nikolas
Reply
12-10-2009, 03:46 PM,
#5
RE: Turbine high speed shaft RPM 6000 to be coating
Hi Nikolas

Sign0016 to the Surface Engineering Forum.

Thanks for your input.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
Pencil Ball Mill Shaft- Journal Bearing Area HVOF Coating Issue tobjung 0 1,054 02-02-2023, 06:44 PM
Last Post: tobjung
  Arc spray or HVOF for bearing of turbine generator shaft Youssef 0 2,255 06-15-2020, 06:08 AM
Last Post: Youssef
  Robot speed & RL turn table calculation demionkrishan 9 12,160 05-12-2020, 07:32 PM
Last Post: Lemster68
  Surface speed Panf 24 54,597 02-03-2020, 09:31 AM
Last Post: DMan
  surface speed for HVOF coating process gito 8 6,249 05-03-2019, 01:08 PM
Last Post: Lemster68
  roller surface high roughness Tungsten carbide coating Ra 0.15-0.3mm zhuminkun 6 5,741 02-08-2019, 04:59 AM
Last Post: Taz
  Gas Turbine Blades HVOF Coating masking demionkrishan 7 7,615 01-17-2018, 01:09 AM
Last Post: Taz
  opening blocked cooling holes in Stage 1 gas turbine blades Gustavo Woltmann 1 3,007 03-07-2017, 08:27 AM
Last Post: loriolo
  opening blocked cooling holes in Stage 1 gas turbine blades demionkrishan 1 3,334 03-04-2017, 07:44 AM
Last Post: loriolo
  Propeller shaft repair by flame spray in the cones area Iwan Sedaryawan CA 1 3,366 12-09-2016, 04:56 AM
Last Post: Stephen Booth
  turbine blades and vanes HVOF appliaction anne 4 4,726 12-02-2016, 05:54 PM
Last Post: demionkrishan
  turbine rotor gland seal system, Stephen Booth 1 4,804 06-20-2015, 06:47 PM
Last Post: Johnny_Blaze
  Masking tape for high-heat ceramic coating. texnicar 1 4,422 04-21-2015, 04:09 PM
Last Post: cris1904
Information Hydraulic Shaft - Thermal Spray - Advice needed Jagdeep 2 5,392 10-09-2013, 07:16 PM
Last Post: shantanu
  High velocity thermal barrier coating djewell 2 5,499 09-04-2012, 07:50 PM
Last Post: farzin_g1



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd