Thermal Barrier Coating Aluminum Substrate for corrosion resistance
02-24-2015, 03:27 AM,
#1
Thermal Barrier Coating Aluminum Substrate for corrosion resistance
Hello,

I've read this board here and there and did as much searching as one can do on the internet as well as on this forum. I was not lucky enough to find the answer that I am seeking. If I missed low hanging fruit, please excuse me for missing it.

I have a component made of aluminum that is experiencing accelerated corrosion as a result of the environment it lives. This component is used as an exhaust cone, yes I know... why Al?!, and operates at around 200F. The corrosion is likely the result of a few things but I am willing to guess at this point. I believe the exhaust gases, thermal cycling and anodized coating are all a factor. My hope is that someone here knows a little about using thermal barrier coatings (TBC) on internal combustion engine components made of aluminum.
I am aware of TBCs use in internal combustion engines but TBC coatings are not used, to my knowledge and research of multiple OEM manuals, on turbine engine aluminum components. All turbine section parts (except this exception!) are not made of aluminum.

I have to be slightly vague for obvious reasons for I'll sum it up again:
Aluminum substrate operating at 200F
Seeking TBC coating/method to protect the substrate surface exposed to hot exhaust gases.

Thank you for any thoughts you might have!

AG

Reply
02-24-2015, 09:18 AM,
#2
RE: Thermal Barrier Coating Aluminum Substrate for corrosion resistance
Dear alaskangrown,

I propose a new thermal barrier and corrosion-proof coating for aluminum, designed to protect of pistons from internal combustion engines.

Properties of the coating:

Hardness (20°C): 350-380 HV0,2
Elastic modulus (20°C): 95-102 GPa
The strength of the four-point bending (20°C): 220-250 MPa
The strength of the four-point bending (550°C): 190-210 MPa
Bond strength to the Al-substrate (20°C): 100-150 MPa (corresponds to the strength of cast aluminum alloys Al-Si)
Specific heat (20°C): 0,57 J/gK
Thermal diffusivity (20°C): 1,9 mm2s-1
Thermal conductivity (20°C): 4,9 W/mK
Density (20°C): 4,8 g/cm3
Porosity: < 0,5%
The maximum temperature at the interface with the AlSi-substrate: 500°C
The maximum temperature on the surface of the coating: 800°C


The coating is applied by atmospheric plasma spraying (optimally at device - Axial III). Coating thickness can choose between 0,1-3 mm.

Coating intended to reduce the temperature on the surface of the piston and enhancing engine efficiency. Furthermore, the coating protects the surface of the piston against corrosion in combustion products comprising sulfur.

Regards

Vadim Verlotski
   
Reply
02-26-2015, 01:37 PM,
#3
RE: Thermal Barrier Coating Aluminum Substrate for corrosion resistance
Whom is the coating's manufacture and does it have a name?
What is the general chemical composition?

Reply
02-26-2015, 04:41 PM, (This post was last modified: 02-26-2015, 06:57 PM by Vadim Verlotski.)
#4
RE: Thermal Barrier Coating Aluminum Substrate for corrosion resistance
(02-26-2015, 01:37 PM)alaskangrown Wrote: Whom is the coating's manufacture and does it have a name?
What is the general chemical composition?

The coating is produced by Märkisches Werk GmbH (patent 2008). The coating consists of three phases: nichrome, silicate glass and cristobalite.

.pdf   US20140302299A1.pdf (Size: 359.89 KB / Downloads: 563)
   
Reply
03-02-2015, 06:43 PM,
#5
RE: Thermal Barrier Coating Aluminum Substrate for corrosion resistance
Thank you Vadim
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Corrosion Problem on HVOF Coating (DJ2600 Metco Gun) xxxxmgulkokan 5 2,367 04-03-2022, 12:45 PM
Last Post: sprayjet
  Yellow Spot on Thermal Barrier Coating achmadarifudinh 11 4,836 11-30-2020, 05:32 PM
Last Post: Lemster68
  Ceramic Coating on Aluminum Base metal demionkrishan 9 4,742 02-03-2020, 09:35 AM
Last Post: DMan
  Substrate preparation VS bonding strength plzc126330 2 3,343 01-09-2018, 03:48 AM
Last Post: plzc126330
Lightning Aluminum Foil wrapping as corrosion protection instead of coating LouisRichter 2 8,284 09-22-2017, 11:07 AM
Last Post: madan.pal
  Thermal spray coatings over carbon fiber substrate Hector Monjardin 5 6,616 11-18-2015, 04:00 PM
Last Post: Hector Monjardin
  Thermal barrier delamination problem Hector Monjardin 2 4,444 09-25-2015, 11:05 AM
Last Post: Joris Kraak
  Appling The WC hard coating on Hard substrate behzadsaberi 3 4,662 04-24-2015, 06:04 AM
Last Post: Vadim Verlotski
  Coating for Epoxy substrate webrits 2 4,104 03-20-2015, 03:09 PM
Last Post: Laurent
  Pure Aluminum on GFRP Composite Substrate ahmadsahid 4 5,439 05-01-2014, 01:34 PM
Last Post: Gordon
  coating Al cylinder for wear resistance sal 7 8,190 09-08-2012, 06:58 AM
Last Post: sal
  High velocity thermal barrier coating djewell 2 5,165 09-04-2012, 07:50 PM
Last Post: farzin_g1
  coating of aluminum cylender ehsan 2 4,254 11-13-2011, 01:26 PM
Last Post: ehsan
  substrate deformation of WC coating in gate valve ehsan 2 5,958 12-14-2010, 09:15 AM
Last Post: Asiaf
Cool Instrument to check coating thickness of Thermal Barrier Coatings odski0317 5 17,687 12-01-2010, 10:09 AM
Last Post: dienngothe



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd