Technical Characteristics of Rich Laser Cladding Technology
05-17-2014, 06:15 AM,
#1
Technical Characteristics of Rich Laser Cladding Technology
Technical Characteristics of Rich Laser Cladding Technology
  Rich laser metal cladding technology adopts miniwatt YAG pulse laser as heat source for metal cladding. Compared with traditional metal defect repairing technologies, there are the following advantages:
1. Comparison with Large-size Laser Equipments
  Large-size laser cladding equipment adopts CO2 continuous laser as heat source, whose wavelength is 10 times of that of miniwatt YAG laser. For that metal’s absorptivity of different wavelength laser, miniwatt YAG laser, whose wavelength is 1/10 of CO2 laser’s, can form high-temperature molten pool more easily in ultrashort time since short wavelength and concentrated pulse energy, thereby, heat affected zone would be more easily controlled in quite a small area, crystal phase would be organizational exquisite, pore-free and no slag inclusion, and matrix no distortion.

  For that YAG laser adopts pulse mode, its facula strength, acting time and waveform can all be preset, which helps to control facula’s heating and cooling methods on metal matrix, therefore, effects and control of metal phase transformation can reasonably realize.
  Price of Rich laser equipments is only one tenth of large-size lasers. Small in size, light in weight, and low in operating cost, for what it’s more convenient for transporting to site and realize repairing without disassembling.
2. Comparison with Thermal Spraying Technology
  Rich laser metal cladding technology can genuinely form sufficient molten pool, and realizes metallurgical bonding which can improve bonding strength and compactness between cladding material and matrix.
Spraying coating, bombarded by laser facula, can realize ideal metallurgical cladding result. The combination between Thermal Spraying Technology and Rich Laser Cladding Technology can bring the advantages of these two technologies into full play, and realize ideal result of metal surface repairing.
Hebei Richcause Technology Co.,Ltd
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Mechanical cladding Artyom 0 825 02-27-2019, 08:18 AM
Last Post: Artyom
  The Ps-PVD Technology mgbaca1a 0 920 09-23-2018, 05:11 PM
Last Post: mgbaca1a
  Laser cladding plungers Arturas 2 2,983 09-24-2016, 09:49 AM
Last Post: Vadim Verlotski
  Zinc arc spray vs Zinc-rich silicate or epoxy paint KeDuan 1 2,382 04-23-2016, 06:05 AM
Last Post: Stephen Booth
  Laser thermal cycle test Max K 0 1,968 03-01-2016, 04:03 PM
Last Post: Max K
  Technology of Flame Spray -old and new Boris Eizner 0 2,319 01-29-2015, 10:04 AM
Last Post: Boris Eizner
  Technical Bulletin of Metcoloy 2 wire Met.Eng. 4 7,515 05-21-2014, 08:14 AM
Last Post: Stephen Booth
  Features of laser cladding lijianping 0 2,088 05-14-2014, 09:15 AM
Last Post: lijianping
  Laser metal cladding rechnology lijianping 0 3,134 05-14-2014, 09:01 AM
Last Post: lijianping
  Laser Cladding onto 17-4 PH Grayso 4 6,398 03-01-2014, 11:09 AM
Last Post: makankp
  Metco Technical Bulletins plasmajet1990 2 6,582 02-13-2013, 01:53 PM
Last Post: loriolo
  Metco 206A Technical Bulletin plasmajet1990 0 2,342 02-11-2013, 08:58 PM
Last Post: plasmajet1990
Question about induction cladding littlejialei 5 6,731 03-12-2011, 01:50 AM
Last Post: Gordon
  Laser Cladding Stellite#6 Kedarnath 6 17,387 02-04-2011, 01:51 PM
Last Post: Nick4u1
  general characteristics of TS coating Jaydev 9 6,431 05-01-2010, 05:31 AM
Last Post: Jaydev



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd