Erosion-corrosion issues in boiler applications
05-04-2010, 10:01 AM,
#1
Erosion-corrosion issues in boiler applications
Dear Forum members:

I wish to know the latest developments in terms of materials for combating erosion-corrosion issues in boiler applications. As i understood from discussions with experts from a leading powder manufacturer that Cr3C2-Inconel is the latest material, having a potential to replace fine grained Cr3C2-25NiCr and i wish to know your field experience on the above materials. And your thoughts on potential materials for such applications will be of immense help to my research..

With advance thanks...

Sivakumar
Reply
05-04-2010, 08:40 PM,
#2
RE: Erosion-corrosion issues in boiler applications
Corrosion-erosion of boiler tubes cannot be reduced to a simple "best material". There are a wide variety of factors that play into best selection including, but not limited to:

1) What is the fuel in this boiler? Most likely you are referring to coal, but other fuels introduce different issues.
2) What is the composition of the atmosphere inside the boiler? Inconels are often good selections, but there are pitfalls that you don't want to fall into.
3) Where in the boiler are you talking about? Corrosion-erosion behaviors and solutions may be very different for instance in sootblower lanes as opposed to at the bull nose.
4) Presumably this is for a research paper and not application specific, therefore I would suggest that in general you are on the right track. One thing that cannot be stressed enough is that in most environments the material selection is less important than making sure that the application is executed with a sound quality control plan.
5) **Caution, rumor and speculation**While I have no direct knowledge of them I have heard rumors of some studies being conducted on gradient type coating systems. This requires special equipment and is mostly R&D technology to the best of my knowledge. I haven't looked for any specific papers on it, but if you are trying to assemble a paper on "best technologies" then you may find value here.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
Shy HVOF Coating Calender Roll issues. Suggestion needed tobjung 1 537 02-10-2021, 02:03 PM
Last Post: Lemster68
  Spray & Fuse coating for Boiler tubes Jaydev 8 8,477 05-10-2020, 08:14 PM
Last Post: SENTESBIR-POWDERS
  Boiler tube failure Flo24 8 13,991 06-22-2019, 01:19 PM
Last Post: velocity
  Favourite and challanging spraying applications velocity 3 1,224 04-30-2019, 10:26 AM
Last Post: Stephen Booth
  BOILER TUBE COATING ehasan 4 15,610 11-14-2017, 03:24 AM
Last Post: Stephen Booth
  coating Fluidized Bed Combustion Boiler tubes iwan-sedaryawan 9 8,083 09-18-2017, 05:01 AM
Last Post: Stephen Booth
  Erosion due to drilling mud Dondomobilus 1 3,272 05-29-2014, 07:07 PM
Last Post: djewell
  Erosion Test of an Abradable Coating baaddin 3 4,537 02-11-2014, 07:32 AM
Last Post: baaddin
  Applications of Chrome Plating ritesh 5 4,649 05-29-2013, 09:17 AM
Last Post: Laurent
  coatings WC-Co - applications in my case? pashamt8 5 5,079 05-07-2012, 02:49 PM
Last Post: saintGeorge
  Issues in Al coating on photoresist xoobiii 5 4,236 03-13-2012, 10:26 AM
Last Post: loriolo
  Surface prep issues before APS coating msiranni 6 5,929 06-21-2011, 12:56 PM
Last Post: Justin
  fresh-water corrosion, pitting and erosion Met.Eng. 5 10,509 05-29-2011, 05:45 PM
Last Post: Gordon
  Coating of coal Boiler tube wall iwan-sedaryawan 6 7,814 05-10-2011, 07:16 AM
Last Post: A.Termika Ltd
  Refuse Incineration (Waste to energy) Boiler Coatings MichiganMan 4 7,006 09-26-2010, 05:48 AM
Last Post: Stephen Booth



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd