Which powder should I use with my combustion flame spray gun?
06-02-2009, 04:47 PM,
#1
Which powder should I use with my combustion flame spray gun?
Hi,

I am researching the adhession and cohession properties of thermal sprayed powders using an experimental nozzle. I am using the ASTM C633 test, but have not yet decided on what material I should use for my powder or for my substrate. The gun that I will be using will be a combustion thermal spray gun with a gravity fed powder hopper. Does anyone have any suggestions?

Reid
Reply
06-03-2009, 01:06 AM,
#2
RE: Which powder should I use with my combustion flame spray gun?
Any kind of substrates can be use, but carbon steel plate is more easier to buy in the market, for the powder in my opinion using low-melting point material is good for the trial, such as : Zinc, aluminum etc. the most important is surface preparation in order to achieve higher bonding strength.
Have a nice trial...
Thanks & Regards,
Iwan Sedaryawan - Website : https://www.ciptaagung.com
Happy0193
Reply
06-04-2009, 10:05 PM,
#3
RE: Which powder should I use with my combustion flame spray gun?
Hey Thanks iwan-sedaryawan,

I ended up ordering a NiAl powder (Metco 450 NS) because it was the powder that was used in a similar test that I read about. I'm not sure about the melting temperature, but I'm assuming that it is quite a bit higher that zinc and aluminum. However, it was a powder that Metco said was usable with my gun (Metco 5P II combustion flame spray). I'm assuming that it will still be okay, but I'm still open to any suggestions since I'm still waiting on my powder.
Reply
06-06-2009, 06:05 PM,
#4
RE: Which powder should I use with my combustion flame spray gun?
Hi Reid

The choice I think it will depend on what your experimental nozzle is aimed at doing. The exothermic so called "one step coatings" or "self-bonding" coatings are good and popular coatings through the 5P-II (Metco 450 being in this group). If your experimental nozzle is aimed at say increasing particle velocity, then using a straight alloy or pure metal powder rather than a composited powder may be better choice.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Want consumables for Metco 16E combustion wire system. Turbo Machinery 0 637 06-07-2019, 12:11 PM
Last Post: Turbo Machinery
  coating Fluidized Bed Combustion Boiler tubes iwan-sedaryawan 9 7,480 09-18-2017, 05:01 AM
Last Post: Stephen Booth
  Propeller shaft repair by flame spray in the cones area Iwan Sedaryawan CA 1 1,649 12-09-2016, 04:56 AM
Last Post: Stephen Booth
  Flame spray guns 5P, 5PII, Type N Hector Monjardin 1 2,190 11-17-2016, 10:35 PM
Last Post: mgbaca
  Build up with Powder Flame Spray Met.Eng. 8 8,199 05-30-2016, 12:08 PM
Last Post: Gordon
  Poor flame with Ni-based metallic powder - HVOF process Roy 2 2,908 02-26-2016, 12:30 AM
Last Post: Roy
  Wire Flame spray and Twin Arc spraying wtaz 1 2,758 03-30-2015, 09:41 PM
Last Post: loriolo
  Technology of Flame Spray -old and new Boris Eizner 0 2,131 01-29-2015, 10:04 AM
Last Post: Boris Eizner
  acetylene flow limits for flame spray metco 6c chromalloymachi112 1 2,764 12-04-2014, 12:18 AM
Last Post: Met.Eng.
  How to spray combustion chamber liner Michaellearnstocoat 5 4,166 09-06-2014, 09:24 AM
Last Post: Stephen Booth
  Parameters of Combustion wire gun Turbo Machinery 3 4,233 05-25-2014, 06:07 AM
Last Post: Stephen Booth
  Reduce unmelted particles in Combustion Wire Spray Alberto Villalobos 8 5,634 05-19-2014, 07:21 PM
Last Post: KevinS
  JP5000 combustion tube KevGarty 5 4,785 11-01-2013, 09:19 PM
Last Post: kschewe
  "Flame Spray Handbook" sal 0 2,931 04-28-2013, 07:49 PM
Last Post: sal
  16 E flame spray sal 4 4,460 09-17-2012, 08:32 AM
Last Post: loriolo



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd