Thermal Spraying Plastics
10-27-2011, 02:22 PM,
#1
Thermal Spraying Plastics
Whave a product line which consists of moulded MDF profiles with a polypropylene co-extrusion used to build shutters and during one of the panel fabrication / assembly steps the top and bottom rail of the shutter is cut to size which exposes the MDF. Currently we use a thermal foil to re-seal that edge however it has some disadvantages which is why I'm interested in flame / thermal spraying the exposed area with polypropylene (ideally) or some other thermoplastic to get a better seal. If a solution is found I would implement it in several fabrication plants around the country.

Does anyone have any suggestions on application for this?
Thank You,
Aaron Boyce
ppsaboyce@gmail.com
Plasmapowders
Reply
11-10-2011, 03:59 AM,
#2
RE: Thermal Spraying Plastics
Hi Aaron

I think certainly worth exploring and getting some coatings tested.

This thread may be worth a view

Thermal-Spraying-of-PP-and-PE

Last time I thermally sprayed plastic coatings like this must be 25-30 years ago. I set-up a Metco 5P or may be 6P gun using propane and air instead of oxygen. Can't remember if I was using special or standard hardware though. Tried nylon 11 and some others (unknown, proprietary powders) in various colours. I was pleased with my efforts, appeared to be very good coatings. A little skill was involved though as the coatings needed to be "flame brushed" just after depositing the coating to fully fuse and produce a shiny surface. I also remember water quenching improved the gloss appearance over just a natural cool.

I have seen some dedicated plastic thermal spray kits demonstrated. Very basic large powder tin converted into fluid bed powder feeder feeding a basic propane torch. Cheap and simple but seemed to work well. Not sure who was making them as it was a while ago. The links in the thread above should give you some ideas or maybe just experiment with a powder flame spray gun if you have one.
Reply
11-10-2011, 01:06 PM,
#3
RE: Thermal Spraying Plastics
If you are looking for a system built specifically to spray plastics, rather than trying to build one up yourself, then these guys might be worth a look.
(link dead)

I have no direct experience working with them or the equipment, but it seems to fit.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  HVOF/HVAF Thermal Spraying connoramcguigan 0 2,515 11-13-2018, 05:13 PM
Last Post: connoramcguigan
  YSZ thermal Spraying by HVOF and Flame mgbaca1a 2 2,648 09-24-2018, 08:57 PM
Last Post: mgbaca1a
Question thermal spraying simulation software ??? vladutzu86 4 9,489 02-08-2015, 05:29 PM
Last Post: kyawkyaw
  Thermal Spraying of Silica Nadiir 2 4,968 11-29-2014, 10:58 AM
Last Post: Nadiir
  How to reduce the intersplat boundaries in thermal spraying hustzc 3 5,961 05-16-2012, 01:30 AM
Last Post: Gordon
  How to thermal-spraying with very large area hustzc 3 5,938 08-25-2011, 01:21 PM
Last Post: LEN WOOD
  learner on thermal spraying graham 4 8,014 12-29-2008, 04:29 PM
Last Post: graham
  Thermal spraying copper parts DVB 6 10,810 03-19-2008, 04:50 PM
Last Post: Gordon
  Thermal spraying coating develop William 6 9,527 03-17-2008, 06:03 AM
Last Post: William
  Thermal spraying melrose 2 7,794 01-19-2007, 11:54 AM
Last Post: melrose



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd