The coating problem of screw in exhaust plastic extrusion granulator
10-24-2013, 03:25 AM,
#1
The coating problem of screw in exhaust plastic extrusion granulator
Hi
Granulator is used to make plastic granules which is used to plastic extrusion molding from exhaust plastics which are cut into slices first. Screw is core of granulator. Because of many hard particle in the exhaust plastics, such as stone, metal, screw undergo serious abrasive wear. The biggest of the abrasive have 5mm in length.

We have sprayed WC-CoCr on the surface of screw by JP8000.The quality of the coating is great. The part of screw was deformed in use because of pressure and the coating was peel off.

The hardness of screw in only HRC22, because it can be machininged easily. The hardness of the screw of maybe the reason of failure.
If arise the hardness, how much?
If you have other advice, please help me!
Thank you!

P.S. nitriding is used strengthen the screw but not enough. Cladding can only strengthen the top of screw.
Reply
11-19-2013, 06:56 AM,
#2
RE: The coating problem of screw in exhaust plastic extrusion granulator
Hi

You can increase hardness of the screw very near to 39 HRC and you can carry coating on the same.
The bulk hardness of the screw also increases from 22 to 39 HRC which may help to perform screw better.

Sreenvias
Reply
11-19-2013, 07:42 AM,
#3
RE: The coating problem of screw in exhaust plastic extrusion granulator
(11-19-2013, 06:56 AM)sreenuvundela Wrote: Hi

You can increase hardness of the screw very near to 39 HRC and you can carry coating on the same.
The bulk hardness of the screw also increases from 22 to 39 HRC which may help to perform screw better.

Sreenvias

thanks for your reply.
we are trying to increase hardness of the screw.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Corrosion Problem on HVOF Coating (DJ2600 Metco Gun) xxxxmgulkokan 5 2,382 04-03-2022, 12:45 PM
Last Post: sprayjet
  ceramic exhaust coating soplillorfr 1 2,360 12-06-2020, 01:04 AM
Last Post: Stephen Booth
  Hot cut dies plastic compound Iwan Sedaryawan CA 2 2,626 01-20-2017, 05:29 PM
Last Post: loriolo
  Craking problem in Al2O3+ TiO2 plasma coating Hector Monjardin 4 4,753 09-22-2016, 01:33 PM
Last Post: Hector Monjardin
  Fused coating problem sprayloud 8 7,670 01-22-2016, 10:30 PM
Last Post: KevinS
  Coating delamination problem texnicar 13 11,545 07-07-2015, 10:37 PM
Last Post: Johnny_Blaze
  Metco 450 coating surface problem Yaakov 2 6,723 05-06-2015, 01:54 PM
Last Post: loriolo
  Screw-propeller Mr.N 1 3,149 10-09-2013, 07:13 PM
Last Post: shantanu
  Blistering problem in Chromium Carbide Coating -- Reg sreenuvundela 4 7,604 04-28-2013, 07:14 PM
Last Post: shantanu
  Plastic Spraying KevGarty 5 6,173 04-08-2013, 11:55 AM
Last Post: loriolo
  Plastic Coating over flow / over spray hafizAR85 0 3,452 02-20-2012, 09:03 AM
Last Post: hafizAR85
  Big Screw pumps repair HVoilF 9 13,963 07-01-2011, 01:58 PM
Last Post: mleonardo
  W121 coating - Parameter Problem ir_minja 1 5,842 02-21-2011, 07:25 PM
Last Post: Gordon
  feed screw reinforcing Arturas 5 7,012 08-22-2009, 04:40 PM
Last Post: drramc
Shy PU Coating for plastic LeeWL 2 5,741 02-02-2009, 08:47 AM
Last Post: LeeWL



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd