Surface Speeds and traverse for coating Cro-167
12-20-2011, 03:30 PM,
#1
Surface Speeds and traverse for coating Cro-167
Hello All,

I'm trying to setup surface speeds for coating CRO-167 on cylinders of different sizes and need to know how to determine speeds and feeds for them. i think the desired coating thickness should be around .0005. Any advise would be greatly appreciated. Thanks joe
Reply
12-23-2011, 04:55 AM,
#2
RE: Surface Speeds and traverse for coating Cro-167
(12-20-2011, 03:30 PM)js2know Wrote: Hello All,

I'm trying to setup surface speeds for coating CRO-167 on cylinders of different sizes and need to know how to determine speeds and feeds for them. i think the desired coating thickness should be around .0005. Any advise would be greatly appreciated. Thanks joe

only .0005? a general though is 150-250 surface feet per min
Reply
12-23-2011, 02:15 PM,
#3
RE: Surface Speeds and traverse for coating Cro-167
Hi js2know

CRO-167 is a chromium oxide ceramic powder I believe.
Quote:i think the desired coating thickness should be around .0005
If you mean 0.0005" per pass then yes. In some cases I would aim even lower ~ 0.0002".

There are a number of threads on this topic, I've link to a couple below which may be helpful:

Surface-speed

RPM-Traverse-Calculator-for-Thermal-Spray
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
Lightning WC10Co4Cr HVOF coating leaves some lumps on the surface tobjung 1 914 10-17-2023, 07:32 AM
Last Post: Vadim Verlotski
  surface speed for HVOF coating process gito 8 6,249 05-03-2019, 01:08 PM
Last Post: Lemster68
  Coating for cyclone internal surface Arturas 0 2,174 12-11-2018, 06:58 AM
Last Post: Arturas
  Remove HVOF Coating in airfoil surface blade achmadarifudinh 5 4,322 07-20-2018, 10:51 AM
Last Post: achmadarifudinh
  Coating surface roughness William 9 27,616 12-26-2017, 10:40 AM
Last Post: Vadim Verlotski
  Powder Coating for Surface Table achmadarifudinh 3 4,095 11-28-2017, 12:19 PM
Last Post: Artyom
  Un-common surface pattern on coating failure shantanu 2 4,081 10-06-2016, 02:55 PM
Last Post: Vig
  Boron Carbide as a Surface Coating TCHP222 0 4,135 11-12-2015, 08:06 PM
Last Post: TCHP222
  Metco 450 coating surface problem Yaakov 2 7,109 05-06-2015, 01:54 PM
Last Post: loriolo
  HVOF coating over Induction Hardened surface shantanu 1 4,182 01-30-2015, 08:17 PM
Last Post: djewell
  Surface contact stress limit over an HVOF coating HVoilF 1 5,475 05-22-2013, 02:07 PM
Last Post: djewell
  Surface prep issues before APS coating msiranni 6 8,041 06-21-2011, 12:56 PM
Last Post: Justin
  Inconel 625 coating on flange surface gops123 5 13,350 04-05-2011, 01:54 PM
Last Post: Stuart Milton
Shy Chromium Oxide Coating - Surface Finish Ra values Ian Mc 5 13,151 05-15-2009, 05:17 PM
Last Post: Gordon
  Porous Machined Surface on Part Lower Inner Diameter on Inco 718 Coating Surface Alexangel1226 4 9,343 03-19-2008, 02:05 PM
Last Post: Gordon



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd