Robot Speed
02-09-2010, 01:52 AM,
#1
Robot Speed
Dear Fellows:

Anyone can advise how to determine the robotic arm speed on the flat panel without rotation? Currently I am mostly dealing with cylindrical components, thus there is no problem to determine the RPM and transverse speed. However I wish to know what happen to the flat surface with 'step spraying', how should the speed like? How does it correlate to the OEM recommended surface speed, i.e. 75m/min, to achieve the desire coating properties?

Thank You
Ykang
Reply
02-09-2010, 11:27 AM,
#2
RE: Robot Speed
Depends on the Thermal Spray process, the material being sprayed and also the substrate to some extent. In addition to a relevant scan velocity you must also define step up distance (and correct overlapping) to ensure a uniform deposit. Obviously this depends mainly on the material, parameters and the subsequent width of the 'flame' at deposition.
Reply
02-10-2010, 06:15 AM,
#3
RE: Robot Speed
GlenB:

Well, so how would you suggest the scan velocity and step up distance? any particular formulae or guides to follow?

Maybe you could give some simple examples or calculation here...

Thanks
Reply
02-16-2010, 06:36 PM,
#4
RE: Robot Speed
(02-09-2010, 01:52 AM)ykang Wrote: Dear Fellows:

Anyone can advise how to determine the robotic arm speed on the flat panel without rotation? Currently I am mostly dealing with cylindrical components, thus there is no problem to determine the RPM and transverse speed. However I wish to know what happen to the flat surface with 'step spraying', how should the speed like? How does it correlate to the OEM recommended surface speed, i.e. 75m/min, to achieve the desire coating properties?

Thank You
Ykang

Recommended traverse velocity is the same for flat or cylindrical parts. You do not have to calculate your linear velocity from the 75 m/min - that is your velocity. Your robot will probably require you to enter this as mm/sec. 75 m/min is equal to 1250 mm/sec.

The step distance is the same as you use for cylindrical spraying as well. If you calculate your traverse velocity for a cylinder based on 3 mm traverse per revolution, then use the same 3 mm as your step when spraying the flat panel.
Reply
02-17-2010, 03:09 AM, (This post was last modified: 02-17-2010, 03:10 AM by LEN WOOD.)
#5
RE: Robot Speed
I assume that the process is Plasma? Obviously scan speed varies with Thermal Spray processes and substrate materials, geometries, thicknesses, etc. Some Plasma coatings particularly abradables need to be faster than the norm and static substrate cooling is a factor too.

Step up height should be 1/4 to 1/3 of the width of flame at gun to workpiece impact distance. The 1/4 to 1/3 width of 'flame footprint' overlap on subsequent scans will provide a uniform deposit.

Cheers
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Robot speed & RL turn table calculation demionkrishan 9 12,159 05-12-2020, 07:32 PM
Last Post: Lemster68
  Surface speed Panf 24 54,594 02-03-2020, 09:31 AM
Last Post: DMan
  IRC5 ABB robot issue demionkrishan 0 2,135 09-19-2019, 04:21 PM
Last Post: demionkrishan
  surface speed for HVOF coating process gito 8 6,248 05-03-2019, 01:08 PM
Last Post: Lemster68
  Fanuc Robot M710 1 C/50 moving in Angular Motion demionkrishan 2 3,174 06-01-2018, 01:49 PM
Last Post: audiopop
  surface speed for HVOF Zhiguo 10 15,402 03-05-2011, 05:50 PM
Last Post: ServiceTech
  Metco ALuminum SF wire speed M.Naguib 1 5,730 12-17-2010, 12:56 PM
Last Post: Gordon
  The recommended surface speed M.Naguib 1 9,456 12-14-2010, 09:53 AM
Last Post: kschewe
  Optimum Travers speed Met.Eng. 4 7,417 10-09-2010, 01:37 PM
Last Post: Gordon
  Question about Metco ar2000 robot hamedfazelm 2 6,045 08-31-2010, 10:55 AM
Last Post: loriolo
  Turbine high speed shaft RPM 6000 to be coating iwan-sedaryawan 4 8,237 12-10-2009, 03:46 PM
Last Post: Gordon
  how to increase TBC deposit speed? derek 11 17,405 05-06-2008, 11:26 PM
Last Post: hvofhamid
  Robot in VPS Vessel jeffsays163 1 4,829 03-02-2008, 09:50 AM
Last Post: ycwbycwb



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd