Melting, unmelted AlSi Microstructure Amdry 2010 powder
08-24-2010, 08:29 AM,
#1
Melting, unmelted AlSi Microstructure Amdry 2010 powder
Hi all,
We are studying Metco Amdry 2010 powder.
We have question about the Melting, unmelted AlSi material after spraying.
How did the melting, unmelted AlSi material happen?

Thanks,
Best regards,
William
Regards, William
Reply
08-24-2010, 11:47 AM,
#2
RE: Melting, unmelted AlSi Microstructure Amdry 2010 powder
Hi William,

I'm sure Gordon will add more, but in the meantime....

In a perfect setup the optimal amount of powder will enter the Plasma stream and be sufficiently melted, propelled and deposited onto the workpiece. In a not so perfect arrangement (with worn hardware, lack of calibration, incorrect parameters, hopper/powder line/injector issues, etc, etc) less material will be satisfactorily processed. With Al Si Polyester turbulence can be an issue where previously 'spent powder' re-enters the spray stream and becomes an undesirable component of the coating matrix.

I hope this helps.
Len Wood
METAL MONSTER LTD
BIGGER BETTER FASTER MORE!
Ph: +64 9 4730705
Fax: +64 9 4730706
Email:: len@metal-monster.com
www.metal-monster.com
Reply
08-25-2010, 12:03 AM,
#3
RE: Melting, unmelted AlSi Microstructure Amdry 2010 powder
Hi William

In addition to comments by Len. Unmelted particles are a fact of life. Most good coatings will have some degree of unmelted particles. The reason why, is that the spray process and powders used are not perfect. Powder particles are not perfect in uniformity of size and shape. Larger particles require more heating than smaller particles. Powder feeding and injection is not perfect. The whole process really is a bit chaotic, so we set parameters to cater for the majority and accept a minority of less than perfect. A good coating often displays evidence of a few under-heated particles along with a few over-heated. A poor coating very often will often have a lop-sided relationship between over and under-heated particles.

My use of the word 'perfect' is to mean a system of 100% efficiency or +/- 0 and not an indication that your equipment or powder is less than it should be Smile
Reply
08-25-2010, 08:43 AM,
#4
RE: Melting, unmelted AlSi Microstructure Amdry 2010 powder
Hi Len Wood and Gordon
Thank for your reply.
Your explanation helped me so much.
After polishing the specimen, we used the etched mode to inspect the microstructure. We saw the tan and bluish phase.
Anybody know? What are the tan and bluish phase?
How happen with that?
Thanks,
Best regards,
William,
Regards, William
Reply
08-26-2010, 04:00 PM,
#5
RE: Melting, unmelted AlSi Microstructure Amdry 2010 powder
Hi William

If you referring to phases within the Al-Si alloy matrix, then these will probably be a very rich aluminium phase and a very rich silicon phase. You may better understand by looking at the Al-Si equilibrium diagram. (one here). Which is which will depend on the etchant used.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Amdry 9951. Anyone know the maximum coating thickness Antcarroll 2 1,083 01-29-2021, 08:17 AM
Last Post: loriolo
  Starting parameters for Amdry 718 Cl.B edrazee 2 1,523 03-31-2020, 07:09 PM
Last Post: loriolo
  Need help with microstructure hereticgame 2 2,448 04-11-2017, 07:40 AM
Last Post: hereticgame
  Amdry 9954 for titanium based alloy Bharti Malvi 6 4,433 12-21-2016, 07:39 PM
Last Post: Bharti Malvi
  Help needed on AlSi coating Brian 1 1,782 12-17-2016, 10:47 PM
Last Post: loriolo
  Amdry 962 and Metco 204 NS parameters F1 45° giuiori75 2 7,549 03-24-2016, 04:31 PM
Last Post: Max K
  Turbulent 450ns Microstructure. alvliew 10 6,030 11-17-2015, 12:43 PM
Last Post: Joris Kraak
Shy TBS for Metco 450NS and AMDRY 2010 alvliew 3 3,935 06-14-2015, 10:59 PM
Last Post: Johnny_Blaze
  AMDRY 1718- Hardness alvliew 4 6,993 03-13-2015, 11:21 PM
Last Post: loriolo
  Reduce unmelted particles in Combustion Wire Spray Alberto Villalobos 8 6,842 05-19-2014, 07:21 PM
Last Post: KevinS
Rolleyes improving 72FNS microstructure bigals 12 11,811 04-02-2013, 07:15 PM
Last Post: alan brown
  F4 Gun+Tristar+muticoat+inconel 718+unmelted Bler 0 2,562 07-20-2012, 07:32 AM
Last Post: Bler
  WC/Co Coating Microstructure kriskros 13 12,423 02-28-2012, 07:14 PM
Last Post: sreenuvundela
Shy What is the main factor for affecting the efficiency of melting the powder? Justin 8 6,971 09-26-2011, 06:03 PM
Last Post: sreenuvundela
  AMDRY 500F AYKAC 1 4,197 03-01-2010, 12:26 PM
Last Post: Gordon



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd