How do I do Bond Coat Selection?
03-10-2015, 01:19 PM,
#1
How do I do Bond Coat Selection?
How to configure difference between using a bond coat material selection, Where I have options available as wires of NiAl 95/5, NiAl80/20 & NiCr 80/20.

Please suggest with some points of difference to make this selection easy. I have many applications where different materials to be sprayed but due to higher thickness bond coat needed to be applied.





Thanks

Ravi
Reply
03-13-2015, 01:01 PM,
#2
RE: How do I do Bond Coat Selection?
If you are permitted to use any of the materials you listed I would use 95/5. I apply that material to a thickness of 0.060-0.100 in some cases without loss of bond.
Since NiCr has Cr, I would stay away from it if given the option due to OSHA regs.
The bond coat is only providing a surface finish for the top coat to be adhere to in most cases. It really comes down to what role the top coat is playing. 95/5 should have a bond strength of about 5 - 6kpsi but it can reach 8kpsi.
Reply
03-13-2015, 11:44 PM, (This post was last modified: 03-13-2015, 11:49 PM by loriolo.)
#3
RE: How do I do Bond Coat Selection?
Hi ...
what kind of spray system do you use?, I can supose that is a wire system and what kind?: Flame wire or Arc spray, this is because with arc spray you must use Ni5Al or Cu10Al and you have in both cases a very good bond strenght quite the same (about 60 MPa), it dipend of the application do you need, Cu10Al is used as bond coat in babbitt bearing coatings, now, if you are speaking about a flame wire system, then, you must use Ni20Al, this because the flame temperature is lower than arc spray temp., and aluminum must have with nichel an esotermical reaction and you reach a bond strenght of about 50 MPa, with NiCr, you can reach at least 30 MPa.
Best regards
Luigi
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Recomended bond coat for Metco 81 VFNS top coat achmadarifudinh 9 4,688 07-06-2023, 04:54 PM
Last Post: ServiceTech
  Metallic HVOF bond coat to TBC APS top coat Gas turbines achmadarifudinh 0 1,829 07-08-2019, 08:34 AM
Last Post: achmadarifudinh
  Metco powder code selection GuadalupeSullivan 1 3,852 06-27-2019, 10:24 AM
Last Post: loriolo
  Bond coat for Metco 312NS Bharti Malvi 4 5,046 12-21-2016, 08:51 AM
Last Post: Bharti Malvi
Question Metco powder code selection mohsen hasanzadeh 1 3,038 10-10-2016, 09:15 PM
Last Post: loriolo
  Diamond Wheel Selection Met.Eng. 1 3,393 06-01-2016, 04:11 PM
Last Post: shantanu
  Coating selection texnicar 2 3,648 11-06-2015, 03:07 PM
Last Post: Johnny_Blaze
  Delamination in the bond coat sprayed on a Ti specimen Justin 9 10,189 01-06-2014, 10:00 PM
Last Post: KevinS
  I need advise on control of metco 405 bond coat Amoros 4 7,116 12-01-2011, 02:08 PM
Last Post: EmilyWatson
  Oxide anomalies in bond coat JBross 5 7,497 11-28-2011, 06:16 PM
Last Post: JBross
Shocked Cracks! in bond coat Christine 5 8,291 11-28-2011, 11:26 AM
Last Post: landemarre
  Possibility Study to use Stellite - 306 Bond Coat for 75Cr3C2 -25NiCr Top Coat -Reg sreenuvundela 2 5,925 09-14-2011, 05:36 AM
Last Post: sreenuvundela
  F50TF50 bond coat Harvey 6 9,797 07-10-2009, 07:01 PM
Last Post: derek
Sad Dark grey particles in Ni-Al bond coat? fhyuan 9 12,276 01-18-2009, 07:02 PM
Last Post: Gordon
  oxide stringers in the bond coat fhyuan 5 11,234 03-18-2008, 04:40 PM
Last Post: Jerrythespritzer



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd