High Pressure Cylinder Compressor Walls Repair
05-22-2012, 06:50 PM,
High Pressure Cylinder Compressor Walls Repair
Dear SEF members,
our costumer needs to repair a 3Rd stage natural high pressure cylinder compressor working in the following conditions:

Inlet gas pressure : 1200 to 1500PSI
Discharge pressure: 2300PSI
Compressor RPM : 1200 Max gas temperature: 185ºF
Cylinder Diameter : 7,25"
Compressed Gas: natural gas
Piston Rings material : Teflon

We have been repairing the compressor cylinder walls using an arc spray high carbon steel coating,ground and honed . After few hours of operation was found that the piston rings were damaged by premature wear due the porosity of the arc coating of the cylinder surface.
We guess if the correct coating for this application would be a Plasma sprayed ground and honed coating. If so could anybody suggest the correct coating procedure and the spraying techniques as:
Required air extraction flow to avoid oxide entrapment into the coating.
Coating suggested thickness
Coating material friendly to the Teflon piston rings?
Required surface finish

Any technical suggestion is welcomed. Does anybody have experience in similar applications? Is the thermal spraying technology well suited for application like the showed in this post?

05-29-2012, 06:33 PM,
RE: High Pressure Cylinder Compressor Walls Repair
Hi HVoilF

Quote:Coating material friendly to the Teflon piston rings?

Could you expand on this part? Teflon is extremely soft by itself with poor wear resistance.
05-29-2012, 09:54 PM,
RE: High Pressure Cylinder Compressor Walls Repair
Thanks Gordon. The fact is that D/R manufactures this third stage high pressure cylinders with "glass Teflon" I don't really know which material is but for sure is harder than pure Teflon..I am trying to get more info about this material,it hardness and it properties. Do you know if somebody repair high pressure cylinders with some thermal spray procedure?

Possibly Related Threads…
Thread Author Replies Views Last Post
  Inconel 625 Plasma Sprayed Compressor Cylinder (ID) demionkrishan 4 1,828 06-17-2019, 01:32 PM
Last Post: demionkrishan
  Hopper Pressure Lower than Gun Pressure devinrist 4 5,283 01-03-2016, 05:45 AM
Last Post: Johnny_Blaze
  Pressure Regulators? Edson 3 3,207 01-03-2016, 05:32 AM
Last Post: Johnny_Blaze
  acetylene cylinder heating blankets chromalloymachi112 2 3,379 12-20-2014, 08:21 AM
Last Post: loriolo
  Consumables for cylinder block made of grey cast A_Hanert 2 3,238 06-25-2014, 10:19 AM
Last Post: A_Hanert
  SPM for MG cylinder Vijay Deshpande 10 14,176 08-19-2013, 12:34 PM
Last Post: Gordon
  coating on zinc bath pot walls shantanu 2 3,120 07-03-2013, 10:47 AM
Last Post: plzc126330
  coating Al cylinder for wear resistance sal 7 6,890 09-08-2012, 06:58 AM
Last Post: sal
  High Pressure Piston Rods HVOF coatings HVoilF 14 21,915 12-24-2011, 10:20 AM
Last Post: k09
  HVOF Powder for Block Engine and Cylinder Liner minh_8888 1 3,642 06-21-2011, 02:28 PM
Last Post: Met.Eng.
  85/15 Zn/Al pressure vessel coating spencew 5 7,549 04-01-2011, 06:28 PM
Last Post: MichiganMan
  Peel of coating during pressure testing raviswanadha 6 7,962 01-14-2011, 08:49 PM
Last Post: Gordon
  Jet Kote O2 and H2 supply pressure requirements? Intel55 1 4,147 06-26-2009, 03:32 PM
Last Post: Intel55
  coating cylinder heads mitch 5 6,196 10-07-2008, 03:15 AM
Last Post: mitch
  What's maximum pressure loading for WC10Co4Cr? deepskysea 2 5,275 09-04-2008, 10:32 AM
Last Post: deepskysea

Users browsing this thread: 1 Guest(s)

Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd