Flame Spray with Liquid Precursor
03-26-2009, 11:44 AM,
#1
Flame Spray with Liquid Precursor
Hi,
Tomorrow i will try a new technique in thermal spray. Flame Spray with liquid precursor Al2O3 to 304S.S substrate. I use as feedstock aluminum nitrate dissolved in isopropanol (flammable)
Can anyone help me how dangerous this could be?Do i have to dissolved it in distilled water before i use it?I'm afraid that this will be a problem to the organic solution cause is not resoluble in water..Any advise will be helpfull. Smile
I will inform you about my results..if anyone interested
(hope to be alive after this attempt..hehe)

Regards..
Reply
03-26-2009, 05:25 PM,
#2
RE: Flame Spray with Liquid Precursor
Hi Aioa

Sounds like an interesting, although possibly exciting/risky project Big Grin

No experience or good knowledge with your particular set-up or aluminium nitrate, so my comments should not be relied upon.

First, aluminium nitrate is a strong oxidising agent so I would have concerns with mixing/dissolving in isopropanol or other organic solvent.

(fuel + oxidant = Mad0233 )

Really not sure on stability here, but I sense risk. If you must Cool very small scale first Happy0193

May be worth just trying water based solution by itself. Although, this will be acidic so you will need to be careful what this comes into contact with.

Make sure you have good extraction/personal protective equipment, as I'm sure you know oxides of nitrogen will be a bye product as well as your intended nano-sized aluminium oxide.

I would certainly be interested in how you get on and just advise to keep it really small scale to start with, just in case the worst happens. Good luck.
Reply
03-27-2009, 08:56 AM,
#3
RE: Flame Spray with Liquid Precursor
(03-26-2009, 05:25 PM)Gordon Wrote: First, aluminium nitrate is a strong oxidising agent so I would have concerns with mixing/dissolving in isopropanol or other organic solvent.

(fuel + oxidant = Mad0233 )

Really not sure on stability here, but I sense risk. If you must Cool very small scale first Happy0193

May be worth just trying water based solution by itself. Although, this will be acidic so you will need to be careful what this comes into contact with.

Make sure you have good extraction/personal protective equipment, as I'm sure you know oxides of nitrogen will be a bye product as well as your intended nano-sized aluminium oxide.

I would certainly be interested in how you get on and just advise to keep it really small scale to start with, just in case the worst happens. Good luck.

Hey Gordon,
I think you are right but i don't know the results for spraying aluminum nitrate dissolved in distilled water..Today is a hard day..I have to believe that the high pressure in precursor (2-3 bar) should be enough for leave the flame outside..I'll try to keep low oxide/fuel to my torch..
Thanks for your advise..
Hope everything to be alright.

See you all later..Smile
Reply
03-27-2009, 12:44 PM,
#4
RE: Flame Spray with Liquid Precursor
Unfortunalety they don't let me do this today..
I have to wait until next week :'( (to improve the safety of the factory..)
So see you next week Smile

Regards..
Reply
03-27-2009, 08:46 PM,
#5
RE: Flame Spray with Liquid Precursor
Hi Aioa

(03-27-2009, 12:44 PM)aioa Wrote: Unfortunalety they don't let me do this today..
I have to wait until next week :'( (to improve the safety of the factory..)
So see you next week Smile

Regards..

Hope to see you next week Happy0193 Seriously though, make good your health and safety and assess risk. Best being over prepared in situations like this is better than being caught out. We don't mind your gun melting down, but we would like to see you back on the forum healthy Smile Good Luck.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Staring procedure for 6p-II flame spray mgbaca1 0 447 01-23-2024, 08:11 PM
Last Post: mgbaca1
  Assembling a second-hand zinc flame spray setup? Gasket 6 1,978 01-22-2024, 12:09 PM
Last Post: MarkDattilo
  Flame spray parameters TurbineRepair 12 23,057 12-10-2022, 05:27 AM
Last Post: SakshiVerma
  Propeller shaft repair by flame spray in the cones area Iwan Sedaryawan CA 1 3,387 12-09-2016, 04:56 AM
Last Post: Stephen Booth
  Flame spray guns 5P, 5PII, Type N Hector Monjardin 1 4,210 11-17-2016, 10:35 PM
Last Post: mgbaca
  Build up with Powder Flame Spray Met.Eng. 8 11,273 05-30-2016, 12:08 PM
Last Post: Gordon
  Liquid fuel hvof testing Parat Tech 0 3,369 05-19-2015, 10:50 AM
Last Post: Parat Tech
  Wire Flame spray and Twin Arc spraying wtaz 1 4,571 03-30-2015, 09:41 PM
Last Post: loriolo
  Technology of Flame Spray -old and new Boris Eizner 0 3,593 01-29-2015, 10:04 AM
Last Post: Boris Eizner
  acetylene flow limits for flame spray metco 6c chromalloymachi112 1 4,452 12-04-2014, 12:18 AM
Last Post: Met.Eng.
  "Flame Spray Handbook" sal 0 5,270 04-28-2013, 07:49 PM
Last Post: sal
  applicatiion of liquid boriding alae9k 0 3,084 12-24-2012, 09:18 AM
Last Post: alae9k
  16 E flame spray sal 4 7,018 09-17-2012, 08:32 AM
Last Post: loriolo
  Powder Flame Spray for Ceramics Met.Eng. 9 11,746 09-19-2011, 04:46 PM
Last Post: Gordon
  Machining for Aluminum Bronze wire flame spray iwan-sedaryawan 3 8,464 01-12-2011, 11:47 AM
Last Post: iwan-sedaryawan



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd