F4 Gun Process Parameters required for Metco 2043 Powder
01-03-2014, 08:41 AM,
#1
F4 Gun Process Parameters required for Metco 2043 Powder
Hai Friends,

I want to coat Metco 2043 powder with our F4 Torch Plasma Spray gun of AMT make.

Kindly share process parameters for the same if you already done the same.

Regards,

SREENIVAS
Reply
01-16-2014, 11:02 PM,
#2
RE: F4 Gun Process Parameters required for Metco 2043 Powder
Hi Sreenivas
I use this parameters: Powder injector 2mm, Distance 8 mm, angle 105°, air cooling parallel 2,6 bar, argon 48 NLPM, H2 4,2 NLPM, 460 amp., 62 V, Carrier 2,8 NLPM, Spreader/suction L55°/601, Spray rate 42 g/min, Spray distance 148 mm.
Best regards
Luigi
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Required Material for Spray demionkrishan 2 1,215 10-22-2020, 08:00 PM
Last Post: sprayloud
  Metco powder code selection GuadalupeSullivan 1 1,137 06-27-2019, 10:24 AM
Last Post: loriolo
  Material Required Calculation Help connoramcguigan 3 1,265 11-21-2018, 09:43 PM
Last Post: sprayloud
  Sulzer Metco 58NS Copper-Nickel-Indium alloy powder question RaymondF2 1 1,567 09-05-2018, 04:35 PM
Last Post: ServiceTech
  Calculating Required Powder for Coating Mud rotors demionkrishan 5 1,983 06-26-2018, 02:36 PM
Last Post: sprayloud
Question Metco powder code selection mohsen hasanzadeh 1 1,902 10-10-2016, 09:15 PM
Last Post: loriolo
  metco 101bns powder / tensile strength RogerMilam 2 2,784 07-23-2016, 11:46 AM
Last Post: RogerMilam
  Amdry 962 and Metco 204 NS parameters F1 45° giuiori75 2 6,751 03-24-2016, 04:31 PM
Last Post: Max K
  Poor flame with Ni-based metallic powder - HVOF process Roy 2 3,119 02-26-2016, 12:30 AM
Last Post: Roy
  Process Parameters for T400 scorpionking 0 2,867 12-17-2013, 04:38 PM
Last Post: scorpionking
  Al-Si Graphit Powder metco 313NS mlavar 4 5,418 09-29-2013, 01:41 PM
Last Post: mlavar
  Process Gasses Purity Impact towards Plasma Spray Process, equipment or outcome Alexangel1226 8 10,315 06-12-2012, 02:46 PM
Last Post: Eric Tolliver
  Parameters that affect the hardness of Metco 204BNS TBC thezombiesprayer 2 5,251 02-10-2012, 02:09 AM
Last Post: thezombiesprayer
  least powder amount used in HVOF process hustzc 1 3,001 06-23-2010, 12:35 PM
Last Post: Gordon
  question about powder reaction during plasma spray process greentree 3 5,395 03-13-2009, 05:09 PM
Last Post: Gordon



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd