Build Up without grit blasting
09-24-2011, 12:02 PM,
#1
Build Up without grit blasting
Hi SEF members,

We have a problam about powder flame spray coating.

We have a big diameter of shaft. We want to coat this shaft bear wear with 6P-II with metco 42C. But we cant grid blasting this bearing surface.

Can we coat this bearing surface with 6P-II without grid plasting?
Reply
09-24-2011, 06:32 PM,
#2
RE: Build Up without grid blasting
Hi Metallurgy_eng

Quote:Can we coat this bearing surface with 6P-II without grid blasting?

Yes, but you will need to use a bond coat like Metco 450 or 480 or a "one step" coating like Metco 442 as a replacement for Metco 42. In my mind this on to grit blasted surface should be the way to go.

Really, I would look into getting some portable grit blasting equipment, the type with the brush heads and recirculating unit. I would much prefer to know that the substrate preparation is at its best, maximising bonding and reliability.
Reply
09-25-2011, 06:48 AM,
#3
RE: Build Up without grid blasting
Hi Metallurgy Engg

I support gordon suggestions and portable shot blasting machines also available.

You can think alternatives like knurling, grooving etc for sample preparation and HVOF process is very suitable if you are unable to get good substrate preparation.


Regards,

SREENIVAS
Reply
09-25-2011, 07:15 PM,
#4
RE: Build Up without grid blasting
Dear gordon and sreenivas,

Currently, we only have this opportunity. We can not do grid blasting on this bearing. In fact, I have news for portable blasting device. But i want to know if we do knurling and grooving on the substrate without gridblasting, and use metco 450 ns bond coat and than apply metco 42 c top lyer, Does it work without problems? İs it possible to coat like this?
Reply
09-26-2011, 01:02 PM,
#5
RE: Build Up without grid blasting
Dear Sir
We have experience in the coating on the shafts of large diameter for the conveyor of the plant of the Dead Sea (Israel) . Coating was deposited by our Flame Spray Termika-2 on bearing position. The diameter of the shaft in this area of ​​900 mm. Surface preparation was carried out hand grinder. Surfaces are clean and specially created roughness. You can see the application process on our website.
Reply
09-27-2011, 03:57 AM, (This post was last modified: 09-27-2011, 03:59 AM by kschewe.)
#6
RE: Build Up without grid blasting
You can ruff up the surface with sandpaper, 60 grit etc. Then clean with acetone or similar. Do a bond coat like gordon mentioned.

Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Dimension change after grit blasting TomasCro 7 10,662 07-10-2023, 07:08 AM
Last Post: anilsingh012
  Grit Blasting Parameters DanyGans 3 6,764 08-20-2018, 04:04 PM
Last Post: darexpl
  Build up with Powder Flame Spray Met.Eng. 8 10,593 05-30-2016, 12:08 PM
Last Post: Gordon
  Grit blasting epoxy, carbon fibre and titanium in one cabinet? David Churcher 2 5,515 11-30-2012, 01:42 PM
Last Post: MichiganMan
  Surface roughness after grit blasting Leanne 8 26,858 08-15-2012, 05:28 AM
Last Post: Leanne
  Brush instead grit blasting divanis 4 8,460 11-16-2011, 05:32 PM
Last Post: divanis
  Dirt in the grit blasting machine Aware 7 9,576 05-20-2011, 05:27 PM
Last Post: Aware
  Buffer or build up layers under HVOF Carbide Coatings Stephen Booth 12 18,876 05-19-2011, 11:00 PM
Last Post: Met.Eng.
  Grit Blasting Riz 5 14,631 05-10-2011, 01:14 PM
Last Post: MichiganMan
  Removal of grit after grit-blasting? pulaunias 11 23,244 06-18-2010, 01:52 AM
Last Post: Gordon
  grit Blasting 13cr steel hibberd 3 6,719 04-14-2010, 07:51 PM
Last Post: Gordon
  tooling wear and aluminum build up kenjr 3 8,425 10-17-2009, 08:58 AM
Last Post: drramc
  Increase production rate of Grit Blasting of steel plates Adarsh 4 10,128 07-14-2009, 07:47 PM
Last Post: djewell
  Grit Blasting Titanium rbeale98 3 12,082 04-13-2009, 08:52 PM
Last Post: Gordon
  Alternatives to grit blasting? durkie 8 13,770 03-19-2009, 10:47 PM
Last Post: Gordon



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd