Arc spray or Flame spray.....hmmm
02-07-2008, 08:41 PM, (This post was last modified: 02-07-2008, 10:34 PM by Intel55.)
#1
Arc spray or Flame spray.....hmmm
got a question for someone looking to repair worn surfaces on some large (some are 3 feet wide and 4 feet tall, over 1000#) cast iron and cast steel parts with 420ss, which will then be ground. Also, coating with 316 and 304 ss which will be machined.

Which process would be more economical due the large surface area, flame or twin wire arc?

Overall, would twin arc wire be a better choice?

Any comments, suggestions, etc are welcomed. Smile

I have seen 420ss 1/8"wire going for $2.00/# recently, which is pretty good.
Reply
02-14-2008, 04:05 PM,
#2
RE: Arc spray or Flame spray.....hmmm
Hi Intel55

For this type job I think I would probably choose arc spray.
Reply
02-15-2008, 08:18 PM,
#3
RE: Arc spray or Flame spray.....hmmm
Gordon's right, cos you don't need to prepare gases...
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Arc Spray and then Plasma spray? Is this common? cancun555 2 2,040 06-23-2017, 07:11 AM
Last Post: loriolo
  Propeller shaft repair by flame spray in the cones area Iwan Sedaryawan CA 1 2,154 12-09-2016, 04:56 AM
Last Post: Stephen Booth
  Flame spray guns 5P, 5PII, Type N Hector Monjardin 1 2,719 11-17-2016, 10:35 PM
Last Post: mgbaca
  Build up with Powder Flame Spray Met.Eng. 8 8,970 05-30-2016, 12:08 PM
Last Post: Gordon
  Wire Flame spray and Twin Arc spraying wtaz 1 3,208 03-30-2015, 09:41 PM
Last Post: loriolo
  Technology of Flame Spray -old and new Boris Eizner 0 2,504 01-29-2015, 10:04 AM
Last Post: Boris Eizner
  acetylene flow limits for flame spray metco 6c chromalloymachi112 1 3,255 12-04-2014, 12:18 AM
Last Post: Met.Eng.
  "Flame Spray Handbook" sal 0 3,349 04-28-2013, 07:49 PM
Last Post: sal
  Bonding for Wire Flame Spray using Aluminum pure wire iwan-sedaryawan 3 4,865 12-14-2012, 08:00 PM
Last Post: MichiganMan
  16 E flame spray sal 4 5,121 09-17-2012, 08:32 AM
Last Post: loriolo
  Rod spray Vs plasma spray shantanu 3 4,265 03-30-2012, 02:43 PM
Last Post: Gordon
  Powder Flame Spray for Ceramics Met.Eng. 9 9,381 09-19-2011, 04:46 PM
Last Post: Gordon
  Machining for Aluminum Bronze wire flame spray iwan-sedaryawan 3 6,747 01-12-2011, 11:47 AM
Last Post: iwan-sedaryawan
  Flame spray aluminuim WULF 4 4,937 02-06-2010, 10:02 AM
Last Post: WULF
  Which powder should I use with my combustion flame spray gun? jamaicanarchie 3 5,022 06-06-2009, 06:05 PM
Last Post: Gordon



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd