16 E flame spray
09-09-2012, 11:04 AM,
#1
16 E flame spray
Hi
I am trying to coat steel alloys with 1%C steel and a bond coat NiAl (95/5).
Could anybody help me in using parameters to minimize porosity and best adhesion?
I am using a 15E gun which is very similar to 16E Metco with wire feed controller and 1/8" wires, Oxygen and Acetylene gases.
thanks,

Reply
09-10-2012, 04:01 AM,
#2
RE: 16 E flame spray
Does this help you any ??

(Please see attachment)


All the best

Kev


Attached Files
.pdf   16E Parameters.pdf (Size: 65.35 KB / Downloads: 2,499)
Reply
09-10-2012, 08:50 AM,
#3
RE: 16 E flame spray
Thanks Kev; but does it mean we should not change them at all and with these parameters we will get the best quality?
Regards,



(09-10-2012, 04:01 AM)KevGarty Wrote: Does this help you any ??

(Please see attachment)


All the best

Kev

Reply
09-10-2012, 09:07 AM,
#4
RE: 16 E flame spray
They are the Parameters that Metco would give as per the tech bulletins
If you get hold of that it will give you the hardness etc etc

Best thing to do is have a play with parameters see what suits you best but you would obviously need metallography equipment to find out porosity levels and the likes. Generally with wire flame you'll prob get around 10% porosity (approx)

I'll have a dig through my comp see what Ive got tomorrow (Australia time)

Any probs give me a yell

All the best

Reply
09-17-2012, 08:32 AM,
#5
RE: 16 E flame spray
This are start parameters and if necesary you can change them, in order to achieve the resoult, that becouse gases stecchiometry can change a little.
Best regards
Luigi
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Staring procedure for 6p-II flame spray mgbaca1 0 431 01-23-2024, 08:11 PM
Last Post: mgbaca1
  Assembling a second-hand zinc flame spray setup? Gasket 6 1,925 01-22-2024, 12:09 PM
Last Post: MarkDattilo
  Flame spray parameters TurbineRepair 12 22,941 12-10-2022, 05:27 AM
Last Post: SakshiVerma
  Propeller shaft repair by flame spray in the cones area Iwan Sedaryawan CA 1 3,366 12-09-2016, 04:56 AM
Last Post: Stephen Booth
  Flame spray guns 5P, 5PII, Type N Hector Monjardin 1 4,185 11-17-2016, 10:35 PM
Last Post: mgbaca
  Build up with Powder Flame Spray Met.Eng. 8 11,208 05-30-2016, 12:08 PM
Last Post: Gordon
  Wire Flame spray and Twin Arc spraying wtaz 1 4,549 03-30-2015, 09:41 PM
Last Post: loriolo
  Technology of Flame Spray -old and new Boris Eizner 0 3,579 01-29-2015, 10:04 AM
Last Post: Boris Eizner
  acetylene flow limits for flame spray metco 6c chromalloymachi112 1 4,439 12-04-2014, 12:18 AM
Last Post: Met.Eng.
  "Flame Spray Handbook" sal 0 5,247 04-28-2013, 07:49 PM
Last Post: sal
  Powder Flame Spray for Ceramics Met.Eng. 9 11,652 09-19-2011, 04:46 PM
Last Post: Gordon
  Machining for Aluminum Bronze wire flame spray iwan-sedaryawan 3 8,431 01-12-2011, 11:47 AM
Last Post: iwan-sedaryawan
  Flame spray aluminuim WULF 4 6,310 02-06-2010, 10:02 AM
Last Post: WULF
  Which powder should I use with my combustion flame spray gun? jamaicanarchie 3 6,318 06-06-2009, 06:05 PM
Last Post: Gordon
  Flame Spray with Liquid Precursor aioa 4 7,696 03-27-2009, 08:46 PM
Last Post: Gordon



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd