twin wire arc spraying equipment for stainless steel wire, monel wire, etc.

[technovel]

Dear colleages!
Hope everything is going well with you and your business!
I need to understand what is twin-wire arc spraying equipment the most used for spraying of stainless steel wire, monel wire, etc., in your opinion.
Twin-wire arc spraying equipment must be foolproof and for manual application.
Look forward to your early reply!
Thanks a lot and best regards.

[LEN WOOD]

Hi,

For Arc spray Metallisation (http://www.metallisation.com) are The original and Best; their systems are the most robust, easiest to use and get the best results form. Metallisation arc spray rates and deposition rates are (I'm sure) the highest without the coating integrity trade-off! Metallisation systems are surprisingly the most economical to obtain and run. Technical backup and support is unparralelled.

No I don't work for them, but if you look in the market place they are often 'out marketed' by the major Thermal Spray vendors which is unfair and misleading!

I'm sure others will respond with 'reasons for' .....system!

regards

GlenB

[Alexangel1226]

Technovel,

Depends on your application and requirement and budget, there is not particular OEM are the best for your context. Most of them are good if they are able to suffice your needs, meeting ur budget and giving you the back end service and customer back up whenever you need them.

Personally, I would prefer a push-pull synchronized type arc spray system and it is a patented design by one of the veteran reputable brand. This is because arc spray often enough will have the wire speed not synchronized prob and leads to all kinds of problems and coating defect.

The wire conduit once worn will cause the wire feeding unsmooth and jammed...casuing a mess to the production, need to remove, cut away the wire, replace conduit if needed, re feed, re synchronize manually..to get the smooth feeding again.. .. these were some of the prob I encountered previously, and switching to a push-pull type have solve this prob, giving you consistent feeding and most importantly when you are using robots to perform spraying with multple angles.

The down side of it is the gun body is bulky, and manual spraying may not be ideal, need robust and strong arms to perform long operations=P

Just a little comment =)

[Florin]

Alexangel1226 Wrote:Technovel,

Depends on your application and requirement and budget, there is not particular OEM are the best for your context. Most of them are good if they are able to suffice your needs, meeting ur budget and giving you the back end service and customer back up whenever you need them.

Personally, I would prefer a push-pull synchronized type arc spray system and it is a patented design by one of the veteran reputable brand. This is because arc spray often enough will have the wire speed not synchronized prob and leads to all kinds of problems and coating defect.

The wire conduit once worn will cause the wire feeding unsmooth and jammed...casuing a mess to the production, need to remove, cut away the wire, replace conduit if needed, re feed, re synchronize manually..to get the smooth feeding again.. .. these were some of the prob I encountered previously, and switching to a push-pull type have solve this prob, giving you consistent feeding and most importantly when you are using robots to perform spraying with multple angles.

The down side of it is the gun body is bulky, and manual spraying may not be ideal, need robust and strong arms to perform long operations=P

Just a little comment =)

Hello!

Could you tell me what is the system name/producer you prefer for the wire arc spray? You mentioned above a push-pull system. Thank you for your input! Are you in Europe?

Best regards,
Florin

[Stephen Booth]

Hi Florin, for inside workshop technical wire applications try the SM OSU FlexiArc 300 or 200 for field applications try the EcoArc 350 and 600. Very robust equipment. I have some that are over 20 years and still working fine.

[Florin]

Stephen Booth Wrote:Hi Florin, for inside workshop technical wire applications try the SM OSU FlexiArc 300 or 200 for field applications try the EcoArc 350 and 600. Very robust equipment. I have some that are over 20 years and still working fine.

Hello Stephen,

Thanks for your advice. What is new, how are you doing?

Best regards,
Florin

[adam wintle]

In South Africa we also need something very robust. We have found that the TAFA 8830 system works very well. We have over 20 such units in SA. This could be one of the reasons why people are making copies of this gun. We also find that as TAFA use the ESAB power supply we can get parts from ESAB if required. We don't have too many problems though.