SS 316L Coating thickness measurement
05-10-2007, 12:34 PM,
#1
Question  SS 316L Coating thickness measurement
Hi again!

I have applied SS 316L coating by wire arc spray over carbon steel. But totally failed to measure coating thickness by Magnetic Induction method. The actual thk by micrometer shows 1.05 mm but thk guage shows 0.6++ only. DFT meter was calibrated & recalibrated. It works fine on other coatings.

Can anybody inform -

a) why it is happening?
b) what DFT meter will give correct readings?

Regards,
Reply
05-10-2007, 12:52 PM,
#2
RE: Coating thickness measurement
Hi sumant

316 is an austenitic stainless steel and is normally non-magnetic. Thermal spray coatings produced from this material though show different properties and usually show some ferromagnetic properties unlike its wrought equivalent. It is the coatings magnetic properties that are causing your instrument to give you false low readings of coating thickness. Really, the only way round this is to calibrate your instrument using your actual coating and not with the usual non-magnetic plastic shims.

See this thread
Reply
07-20-2007, 04:14 PM,
#3
RE: Coating thickness measurement
Hi Sumant
I don't know if this is of any value, but just as info. All thermally sprayed coatings are subject to a certain level of forging in the spray process. As higher the particle velocity and inpact force is, that higher the forging effect (unregarding particle size). That is one part of the calculation of the finishing allowance required.
br bjarne
Reply
07-20-2007, 04:25 PM,
#4
RE: Coating thickness measurement
Sumant
One thing more, as Gordon explained, the magnetic properties make a hugh difference. You have to be certain about which measuring system is used for a certain material.
You have also to remember that the ts-coating, because of its splittered construction, does many signals/coils/acustics and so on to behave oddly.
bhe
Reply
07-20-2007, 04:42 PM,
#5
RE: Coating thickness measurement
Still more about thickness measuring.
If trying to use magnetic methods, the only somewhat accurate system is to first make accurate test samples (mechanically measured) for calibrating the magnetic-meter.
Even then one has to remember that the magnetic flow is depending on the material thickness.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  WC-CO-CR hvof coating thickness measurement on Base SS 316L JRB VIRANI 3 1,126 06-20-2019, 09:16 AM
Last Post: loriolo
  TSA coating applied to 316L pipe MIKEOKEEFE63 2 3,028 06-10-2019, 07:25 PM
Last Post: JRB VIRANI
  Roughness Measurement Standard Taz 1 894 02-08-2019, 07:01 PM
Last Post: Lemster68
  Coating Thickness Measurement Equipment Taz 1 1,230 01-09-2019, 07:46 PM
Last Post: Lemster68
  Abradable Coating Thickness limitation wasif 1 2,644 07-28-2015, 10:57 PM
Last Post: Johnny_Blaze
  The thickness of coating minh_8888 5 4,912 03-25-2015, 10:31 AM
Last Post: Dr.Boris A.Eizner
  Drum Thickness Coating Requirement for SS316. samshah 0 1,884 11-13-2014, 04:56 PM
Last Post: samshah
  coating thickness Brent 7 5,606 03-09-2013, 11:56 AM
Last Post: sreenuvundela
  uneven Wc coating thickness Brent 5 4,981 01-20-2012, 04:13 AM
Last Post: KevGarty
  COATING THICKNESS GAUGE ehasan 3 4,577 01-14-2011, 08:07 PM
Last Post: Gordon
Cool Instrument to check coating thickness of Thermal Barrier Coatings odski0317 5 15,259 12-01-2010, 10:09 AM
Last Post: dienngothe
  Coating Thickness Met.Eng. 2 3,377 12-01-2010, 04:17 AM
Last Post: omcblacksmith
  Shot peening and increase in Stainless 316L hardness? bry1975 3 9,161 11-30-2009, 03:22 PM
Last Post: Grettir
  Thickness Measurement of Sprayed Monel wrjordan 15 14,164 11-08-2009, 05:40 AM
Last Post: k09
  ferrous coating thickness gauge ehsan 1 3,429 04-27-2009, 04:15 PM
Last Post: Gordon



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd