Metco 450 coating surface problem
05-05-2015, 11:35 AM,
#1
Metco 450 coating surface problem
Hi,

We spray Metco 450NS using F4 gun
Process parameters are: Current 600A, Ar 40-55, H2 8-9.5, Table speed 40-70rpm, Traverse Speed 2-3mm/min, Distance from the gun 120-170mm and from the center of table 280-35mm.

In all of our attempts the coating had instability (the coating has "ridges" and the his morphology a little bit changed) at the top of the coating.

Any recommendations?


Reply
05-05-2015, 03:58 PM,
#2
RE: Metco 450 coating surface problem
(05-05-2015, 11:35 AM)Yaakov Wrote: Hi,

We spray Metco 450NS using F4 gun
Process parameters are: Current 600A, Ar 40-55, H2 8-9.5, Table speed 40-70rpm, Traverse Speed 2-3mm/min, Distance from the gun 120-170mm and from the center of table 280-35mm.

In all of our attempts the coating had instability (the coating has "ridges" and the his morphology a little bit changed) at the top of the coating.

Any recommendations?


Dear Yaakov,

You can use fine powder (Diamalloy 4008,43F-NS etc.)

Regards


Turgu

Reply
05-06-2015, 01:54 PM, (This post was last modified: 05-06-2015, 02:01 PM by loriolo.)
#3
RE: Metco 450 coating surface problem
Hi Yakov
Try with this parameters

Plasma Gun type F4-MB
Nozzle / Electrode Std. / 6
Injector holder version Std.
Injector 1 | 2 Ø [mm] 1,8
Injector 1 | 2 angle [°] 90
Injector distance radial[mm] 6
Current [A] 600
Argon (Ar) [slpm] 55
Hydrogen (H2) [slpm] 9,5
Spreader / Suction piece L/L
Powder carrier gas 1 | 2 type; [slpm] 3,5
Powder feed rate 1 | 2 [g/min] 50
Stirrer speed 1 | 2 [RPM] 60
Spray distance [mm] 140
Best regards
Luigi
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
Lightning WC10Co4Cr HVOF coating leaves some lumps on the surface tobjung 1 438 10-17-2023, 07:32 AM
Last Post: Vadim Verlotski
  Diamalloy 2004 surface roughness problem Khairul Anwar 2 5,812 06-20-2023, 03:39 PM
Last Post: Lars.Patrick
  Problem with Metco 601NS & F4 paikhuan 10 2,408 06-25-2022, 09:18 PM
Last Post: paikhuan
  Corrosion Problem on HVOF Coating (DJ2600 Metco Gun) xxxxmgulkokan 5 2,367 04-03-2022, 12:45 PM
Last Post: sprayjet
Lightbulb Metco 58NS CuNiIn Interface Problem johnrafiee 18 4,878 03-15-2022, 07:57 AM
Last Post: techmankpo
  surface speed for HVOF coating process gito 8 5,548 05-03-2019, 01:08 PM
Last Post: Lemster68
  Coating for cyclone internal surface Arturas 0 1,874 12-11-2018, 06:58 AM
Last Post: Arturas
  Remove HVOF Coating in airfoil surface blade achmadarifudinh 5 3,837 07-20-2018, 10:51 AM
Last Post: achmadarifudinh
  Coating surface roughness William 9 26,585 12-26-2017, 10:40 AM
Last Post: Vadim Verlotski
  Powder Coating for Surface Table achmadarifudinh 3 3,740 11-28-2017, 12:19 PM
Last Post: Artyom
  Un-common surface pattern on coating failure shantanu 2 3,654 10-06-2016, 02:55 PM
Last Post: Vig
  Craking problem in Al2O3+ TiO2 plasma coating Hector Monjardin 4 4,733 09-22-2016, 01:33 PM
Last Post: Hector Monjardin
  Fused coating problem sprayloud 8 7,656 01-22-2016, 10:30 PM
Last Post: KevinS
  Boron Carbide as a Surface Coating TCHP222 0 3,744 11-12-2015, 08:06 PM
Last Post: TCHP222
  Coating delamination problem texnicar 13 11,514 07-07-2015, 10:37 PM
Last Post: Johnny_Blaze



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd