Info needed on Bond Strength for Thermal Spray powders
10-10-2017, 10:52 AM,
#1
Info needed on Bond Strength for Thermal Spray powders
Hello!
Can anyone say the minimum bond strength required for Stellite-12 and Stellite-6 ?? Sprayed By HVOF

Because for WC-Co-Cr & CrC-NiCr we are getting 10,000 PSI + but for Stellite-12 and Stellite-6 Coating is failing at 7,000 PSI. I dont know whats the minimum requirement . Does anyone know the minimum PSI Needed???

Regards,
Reply
10-10-2017, 11:39 AM,
#2
RE: Info needed on Bond Strength for Thermal Spray powders
(10-10-2017, 10:52 AM)hereticgame Wrote: Hello!
Can anyone say the minimum bond strength required for Stellite-12 and Stellite-6 ?? Sprayed By HVOF

Because for WC-Co-Cr & CrC-NiCr we are getting 10,000 PSI + but for Stellite-12 and Stellite-6 Coating is failing at 7,000 PSI. I dont know whats the minimum requirement . Does anyone know the minimum PSI Needed???

Regards,

Your result is not bad at all. It could be something more, but not much more. For Stellite layers, produced by HVOF, the maximum possible adhesion is approx. 9000 PSI. For the HVOF coatings WC-Co the adhesive strength is possible up to approx. 12000 PSI.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  HVOF T800 Tensile Bond Strength issue wgg237 3 5,929 09-11-2023, 09:18 AM
Last Post: Sail L
  304SS and 420Ss Arc Spray as bond layer for HVOF velocity 1 2,388 07-06-2018, 08:38 PM
Last Post: sprayloud
  Ceramic and metal coating powders JeanRellier 1 2,999 09-20-2017, 06:06 PM
Last Post: Vadim Verlotski
  95Ni 5Al bond strength alaskangrown 1 3,821 01-15-2016, 05:09 PM
Last Post: loriolo
  INFO ON ROKIDE SPRAY SYSTEM ehasan 11 23,033 07-10-2015, 07:39 AM
Last Post: shantanu
Shocked Hard Crome Plating Bond strength Met.Eng. 4 7,819 02-24-2015, 02:37 AM
Last Post: Simon Kim
  Arc Wire Spraying Bond Strength wtaz 4 6,351 12-04-2014, 12:02 AM
Last Post: wtaz
Rolleyes Calculate powder weight needed to spray surface area Zacadoom 2 8,701 11-10-2014, 02:58 PM
Last Post: Zacadoom
  suppliers in the uk for powders bazw 0 2,311 10-19-2014, 09:26 PM
Last Post: bazw
  Abradable Coating-Bond Strength rayudugirish 9 15,028 01-06-2014, 09:55 PM
Last Post: derek
Information Hydraulic Shaft - Thermal Spray - Advice needed Jagdeep 2 5,122 10-09-2013, 07:16 PM
Last Post: shantanu
  Question on bond strength. Ghostwheel 4 6,061 10-13-2012, 10:03 AM
Last Post: kschewe
  Suggest on coating bond strength tester feifei0609 3 5,568 08-14-2012, 03:10 PM
Last Post: feifei0609
  PTA Powders attin 0 2,941 01-31-2011, 07:45 PM
Last Post: attin
  Clogging problems with WC-Co Fine powders Met.Eng. 2 4,990 01-03-2011, 03:09 AM
Last Post: kschewe



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd