DJ2600 Injector life
10-11-2012, 10:32 PM,
#1
DJ2600 Injector life
Hi all,

Running a DJ air cooled gun right now and seem to be having a bit of trouble making our injectors last. We are only getting about 18 hours run time. We are seeing them not chip, but melt and the nozzle also looks a touch melted. I am starting to think our console needs to be calibrated and that our gas mix is running oxygen rich, burning the injector and the nozzle. We run on propelyne.
Can anyone tell me their typical lifespan for injectors and if they agree/disagree with my thoughts?

We spray mainly 86/10/4 +38 -10 with standard parameters from the Metco book.

Thanks in advance
Reply
10-12-2012, 01:31 AM,
#2
RE: DJ2600 Injector life
Check your carrier pressure / flow.

I have seen injectors melt in seconds if there has been an inconsistent flow to the gun

Make sure there are no leaks in your line etc

Reply
10-12-2012, 01:38 AM, (This post was last modified: 10-12-2012, 01:43 AM by pakalano.)
#3
RE: DJ2600 Injector life
(10-12-2012, 01:31 AM)KevGarty Wrote: Check your carrier pressure / flow.

I have seen injectors melt in seconds if there has been an inconsistent flow to the gun

Make sure there are no leaks in your line etc

Good point I have same issues and think I've ruled that out. 90 psi on reg, 80 psi canister pressure. 30 on FM. Had higher pressure before and was basically sandblasting the ID of the injector in 2hrs. I'm not sure that is it.
Another point sorry, even at higher pressure they were burning out. Seems like t must be something else to me......maybe!
Reply
10-12-2012, 02:59 AM,
#4
RE: DJ2600 Injector life
Hi pakalano

Carrier gas flow is important as a means of cooling the injector. Commonly seen people burn these out simply by lighting gun with no carrier gas flowing. Carrier gas needs to be flowing when gun is alight, not just when feeding powder.
Reply
10-12-2012, 03:35 AM,
#5
RE: DJ2600 Injector life
I agree with Gordon and has seen many times at one of my friend's TS facility where the injector partially melt at injection point. They had difficulties igniting gun so carrier gas was set very low so that ignition starts well. I have air cooled gun and never had those issue since we supply/maintain the carrier flow same before/after ignition. If the powder stuck at injector, the carrier flow will drop and lead to melting too.

S.Guna
Reply
10-12-2012, 04:20 AM,
#6
RE: DJ2600 Injector life
Agreed Gordon-we have 20 FM reading when we light the gun then bring it up from there. Please see picture. This is why I'm kind of stuck on the thought that our console my be out of calibration.

[Image: dj-injector-tn.jpeg]
Reply
10-12-2012, 04:43 AM,
#7
RE: DJ2600 Injector life
Dont know if this helps but I have attached the DJ Parameter book

But more than likely main cause would be a carrier gas issue


Attached Files
.pdf   DJ Gun Parameters.pdf (Size: 74.98 KB / Downloads: 6,884)
Reply
10-12-2012, 05:08 AM,
#8
RE: DJ2600 Injector life
(10-12-2012, 04:43 AM)KevGarty Wrote: Dont know if this helps but I have attached the DJ Parameter book

But more than likely main cause would be a carrier gas issue

Thank you for that copy Kev. I believe it's the same one I use. Will review our pressure and flow now and try adjusting it up on carrier gas. If I'm not oxygen rich it is the only other thing it could be I'm guessing. Thanks again I will post my results in after a few hours of run time.
Reply
10-12-2012, 05:19 AM,
#9
RE: DJ2600 Injector life
No worries,

Thing to remember with the Diamond Jet is you will need enough hopper pressure to overcome the back pressure from the gun and allow for a stable flow.

Other than that all I can say is.....Good luck !
Reply
10-12-2012, 02:57 PM,
#10
RE: DJ2600 Injector life
Hi Pakalano

Added image to your post.

Kev would have missed that on his reply.
Reply
10-15-2012, 01:23 AM,
#11
RE: DJ2600 Injector life
Hi All,
Yes, the picture confirmed what my friend was facing. We set the Nitrogen cylinder outgoing pressure at 175psi and 150 at control panel. See if line 14 where it enters plastic tube filter, if powder accumulated there it indicates back pressure. Some leaks take place in the hopper system and better go for calibration.

Thanks
S.Guna
Reply
10-16-2012, 04:13 PM, (This post was last modified: 10-16-2012, 04:15 PM by Spraytube.)
#12
RE: DJ2600 Injector life
Hi

I agree with Guna.

You should be careful, normally you have the differential pressure switch linked to line 14, if the back pressure is higher that the supply pressure, system normally stop.
If there is no detection this could mean that there is some powder locking the axis of this differential pressure switch.

In the best case the powder hose will burn, the next step is the hopper...

Your system should be checked.

Regards
Reply
10-18-2012, 06:28 PM,
#13
RE: DJ2600 Injector life
Well thank you thus far for all of your assistance. We seem to have nipped part of our problem in the bud. By increasing nitrogen flow we have stopped injector burn out. We still have the issue of burning nozzles as shown in my above picture. After 4 hours run time, the nozzles are melting. I am thinking oxygen rich lighting flow, in those 4 hours run time we have only lit the gun 4 times. Maybe an oxygen rich mixture?

Thank goodness no leaks in the system, just too low a flow on nitrogen!
Reply
10-18-2012, 08:59 PM,
#14
RE: DJ2600 Injector life
Time to switch to Hybrid gun Rolleyes ...

Reply
10-18-2012, 09:12 PM,
#15
RE: DJ2600 Injector life
Spraytube, that is what we were traditionally using, but had some issues and are waiting on the arrival of new parts. Hopefully next week.....
Reply
10-18-2012, 10:42 PM,
#16
RE: DJ2600 Injector life
If your nozzle's are burning out, could there perhaps be a restriction in the air flow keeping the gun cool ?

or perhaps not enough air ?
Reply
10-18-2012, 11:08 PM,
#17
RE: DJ2600 Injector life
(10-18-2012, 10:42 PM)KevGarty Wrote: If your nozzle's are burning out, could there perhaps be a restriction in the air flow keeping the gun cool ?

or perhaps not enough air ?
Kev,

To my knowledge we have no restriction, in fact I think we may have too much air that is making the flame oxygen rich, therefore too hot and melting tips. Here is the latest one from 7 hours run time. A side note: The injector looks perfect.



Attached Files Thumbnail(s)
   
Reply
10-18-2012, 11:18 PM,
#18
RE: DJ2600 Injector life
I know this is back to basics stuff but I just thought I'd ask....

Is this a manual lighting set up? If it is when you are lighting it how long do you keep the pilot flame on for before lighting ?

I know with some manual systems if the pilot flame is left on too long the flame can burn back into the nozzle / air cap ?

Things like this when you cant put your finger on the fault I would go back to the beginning/basics. Give your gun a good clean, could possibly be a blockage in the siphon plug ?

I think there could be a number of things its just a process of elimination

Dont know if that helps any
Reply
10-18-2012, 11:28 PM,
#19
RE: DJ2600 Injector life
Thanks Kev this is our thought process at this point too. We do light it manually, but it`s a spark then wide open right away. No dwell. We have gone thru the gun but am going to do it again tonight and focus on that siphon plug. The way the nozzle is melting it`s like the flame is being pushed towards the center to fast, like there is too much air coming thru. Funny thing to me is that at present it isn`t melting the injector. Even in the troubleshooting in the Metco book it says if you have poor nozzle life check air flow, but it doesn`t say if it will be too high or too low!
Thanks for your input, I really do appreciate it.
Reply
10-18-2012, 11:49 PM,
#20
RE: DJ2600 Injector life
Is this a new set up or is it just a new problem on an old system ?

Has there been anything that has changed as regards to supplies to the system Air, Oxy, Fuel ?



Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  NiCrBSi coating by DJ2600 Zhao Yun 6 1,291 12-05-2022, 03:43 AM
Last Post: Zhao Yun
  Spark Issue on DJ2600 HVOF Flame xxxxmgulkokan 3 2,135 08-31-2022, 03:15 PM
Last Post: Red Baron
  Corrosion Problem on HVOF Coating (DJ2600 Metco Gun) xxxxmgulkokan 5 2,382 04-03-2022, 12:45 PM
Last Post: sprayjet
  Parameter Stellite 6 HVOF DJ2600 achmadarifudinh 0 2,637 12-07-2018, 01:36 AM
Last Post: achmadarifudinh
  Help,problem with the injector powder. Kirill 4 5,276 07-31-2015, 06:51 PM
Last Post: loriolo
  HVOF DJ2600 DJ8W powder feeder issue vetrinit 5 8,414 06-17-2015, 04:39 PM
Last Post: loriolo
  JP8000 vs DJ2600 system hustzc 1 4,423 04-09-2015, 07:41 PM
Last Post: djewell
  Life of JP 5000 Gun Parts? RV_DMG 5 7,706 11-14-2014, 03:33 PM
Last Post: hvofhamid
Information Chrome oxide thermal sprayed coatings shelf life Leanne 1 4,404 02-14-2013, 02:18 PM
Last Post: Gordon
  HVOF Barrel Life Span sreenuvundela 4 7,281 11-10-2012, 11:33 AM
Last Post: Rohit Upadhyaya
  parts during life torch hvofhamid 10 12,121 05-29-2012, 06:16 PM
Last Post: Gordon
  Surface preparation and its effect on fatigue life and bond strength WMW 4 8,881 06-29-2010, 08:41 AM
Last Post: drramc
  Powder fluidity and injector clogging (DJ 2700 HVOF gun). pulaunias 7 12,818 04-19-2010, 03:16 PM
Last Post: Gordon
  Jet Kote nozzle life plyer 8 13,456 05-15-2009, 02:30 PM
Last Post: plyer
  Metco 7M Injector J_rock 2 4,938 05-28-2008, 06:08 PM
Last Post: J_rock



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd