DJ2600 Injector life
10-19-2012, 02:03 AM,
#21
RE: DJ2600 Injector life
Pakalano,
Is your gun stand off distance correct? If ok, how about your spray/ gun traverse pattern with relative with part geometry? Is the gun distance is being maintained same all the time, is there any point in spray process where the gun comes too near to the part and the flame deflect toward gun? If this take place, there is possibility of nozzle burn as you are experiencing.

S.Guna
Reply
10-19-2012, 02:23 AM,
#22
RE: DJ2600 Injector life
(10-19-2012, 02:03 AM)Guna Wrote: Pakalano,
Is your gun stand off distance correct? If ok, how about your spray/ gun traverse pattern with relative with part geometry? Is the gun distance is being maintained same all the time, is there any point in spray process where the gun comes too near to the part and the flame deflect toward gun? If this take place, there is possibility of nozzle burn as you are experiencing.

S.Guna

Guna, we maintain a 7 1/2" standoff distance and the traverse is completely automated. The only deflection that could be happening is on the shadow guard. I think they may be at 90degrees to the part and when the gun pauses in it cycle, maybe there is blowback from that. Come to think of it until we moved to the closer standoff as the parameters indicate, this wasn't happening. I will check tomorrow thanks! I would have never thought of this.......
Reply
10-19-2012, 03:39 PM, (This post was last modified: 10-19-2012, 03:41 PM by pakalano.)
#23
RE: DJ2600 Injector life
(10-18-2012, 11:49 PM)KevGarty Wrote: Is this a new set up or is it just a new problem on an old system ?

Has there been anything that has changed as regards to supplies to the system Air, Oxy, Fuel ?
Hi Kev, It's a new DJ gun, Old feeder, old console. The one thing I cannot eliminate is that the console my be the cause, as in it may not be calibrated correctly. I need to get this done to eliminate that possibility. We had a hybrid gun on the same setup and it worked fine, just ran into parts problems and are waiting for more. But I need this to work correctly so I have two setups.
No change on gases or air supply


(10-19-2012, 02:23 AM)pakalano Wrote:
(10-19-2012, 02:03 AM)Guna Wrote: Pakalano,
Is your gun stand off distance correct? If ok, how about your spray/ gun traverse pattern with relative with part geometry? Is the gun distance is being maintained same all the time, is there any point in spray process where the gun comes too near to the part and the flame deflect toward gun? If this take place, there is possibility of nozzle burn as you are experiencing.

S.Guna

Guna, we maintain a 7 1/2" standoff distance and the traverse is completely automated. The only deflection that could be happening is on the shadow guard. I think they may be at 90degrees to the part and when the gun pauses in it cycle, maybe there is blowback from that. Come to think of it until we moved to the closer standoff as the parameters indicate, this wasn't happening. I will check tomorrow thanks! I would have never thought of this.......

Well so much for that theory.......I wasn't aware the gun lifts above the part/shadow guard in its pause during cycle. I guess we start over......

Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  NiCrBSi coating by DJ2600 Zhao Yun 6 1,278 12-05-2022, 03:43 AM
Last Post: Zhao Yun
  Spark Issue on DJ2600 HVOF Flame xxxxmgulkokan 3 2,111 08-31-2022, 03:15 PM
Last Post: Red Baron
  Corrosion Problem on HVOF Coating (DJ2600 Metco Gun) xxxxmgulkokan 5 2,367 04-03-2022, 12:45 PM
Last Post: sprayjet
  Parameter Stellite 6 HVOF DJ2600 achmadarifudinh 0 2,624 12-07-2018, 01:36 AM
Last Post: achmadarifudinh
  Help,problem with the injector powder. Kirill 4 5,268 07-31-2015, 06:51 PM
Last Post: loriolo
  HVOF DJ2600 DJ8W powder feeder issue vetrinit 5 8,399 06-17-2015, 04:39 PM
Last Post: loriolo
  JP8000 vs DJ2600 system hustzc 1 4,409 04-09-2015, 07:41 PM
Last Post: djewell
  Life of JP 5000 Gun Parts? RV_DMG 5 7,685 11-14-2014, 03:33 PM
Last Post: hvofhamid
Information Chrome oxide thermal sprayed coatings shelf life Leanne 1 4,390 02-14-2013, 02:18 PM
Last Post: Gordon
  HVOF Barrel Life Span sreenuvundela 4 7,268 11-10-2012, 11:33 AM
Last Post: Rohit Upadhyaya
  parts during life torch hvofhamid 10 12,113 05-29-2012, 06:16 PM
Last Post: Gordon
  Surface preparation and its effect on fatigue life and bond strength WMW 4 8,875 06-29-2010, 08:41 AM
Last Post: drramc
  Powder fluidity and injector clogging (DJ 2700 HVOF gun). pulaunias 7 12,796 04-19-2010, 03:16 PM
Last Post: Gordon
  Jet Kote nozzle life plyer 8 13,430 05-15-2009, 02:30 PM
Last Post: plyer
  Metco 7M Injector J_rock 2 4,931 05-28-2008, 06:08 PM
Last Post: J_rock



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd