Surface Engineering Forum

  • Alternative Forum Home PageSEF Portal
  • Old S E Message Board ArchivesOld Message Board Archives
  • Search
  • Member List
  • Calendar
  • Help

Current time: 02-22-2019, 04:14 PM Hello There, Guest! (Login — Register)


Surface Engineering Forum / Surface Engineering / Surface Engineering Threads v
« Previous 1 ... 10 11 12 13 14 ... 31 Next »
/ ARC Spray for Bearing seat rebuilding




Post Reply 
Threaded Mode | Linear Mode
ARC Spray for Bearing seat rebuilding
05-10-2013, 08:01 AM
Post: #1
shantanu Offline
Senior Member
*****
Posts: 88
Joined: May 2011
Reputation: 1
ARC Spray for Bearing seat rebuilding
Hi All,

A customer requires a bearing seat to be rebuilt to approximately 5 mm on diameter. The bearing fitment procedure is such where in I.D. of the bearing is heated for expansion (temp not known) and then placed over the seat of the shaft. On cooling (again, whether cooling is rapid or atmospheric not known), the bearing shrinks and clasps the seat.
What material would be recommended to repair such a seat and what are the chances of a thermal sprayed coating failing due to the expansion and contraction due to the heat of the bearing. Also, the coating would be 2.5 mm thick, hence probably less elastic than a thinner coating.
I was contemplating a material like TAFA 95 MXC....comments would be helpful
Regards

Shantanu
Send this user an email Find all posts by this user
Quote this message in a reply
05-13-2013, 11:15 PM
Post: #2
loriolo Offline
SuperMember
******
Posts: 268
Joined: Jan 2010
Reputation: 3
RE: ARC Spray for Bearing seat rebuilding
Hi shantanu
Bearing to be mounted on shaft with some interference, ussually are heated in hot oil, at about 120 °C, so there is not problem to apply an adeguate material, it can be Tafa 95 or sulzer Metcoloy 2, both work very well , ther is not problem with thermal expansion.

Best regards
Luigi
Send this user an email Visit this user's website Find all posts by this user
Quote this message in a reply
05-15-2013, 04:18 PM
Post: #3
HVoilF Offline
Active Member
****
Posts: 15
Joined: Mar 2008
Reputation: 0
RE: ARC Spray for Bearing seat rebuilding
Hello ,I agree with Luigi, no problem with this application if the bearing is heated in an oil bath at some 120-150ºC Probably the best material would be Stainlees steel 420 (Metcoloy 2)over a bond coat of Ni-Al ,flame or arc sprayed. The coating will any way works in compression,no problem at all!
Send this user an email Find all posts by this user
Quote this message in a reply
05-15-2013, 06:51 PM
Post: #4
shantanu Offline
Senior Member
*****
Posts: 88
Joined: May 2011
Reputation: 1
RE: ARC Spray for Bearing seat rebuilding
(05-15-2013 04:18 PM)HVoilF Wrote:  Hello ,I agree with Luigi, no problem with this application if the bearing is heated in an oil bath at some 120-150ºC Probably the best material would be Stainlees steel 420 (Metcoloy 2)over a bond coat of Ni-Al ,flame or arc sprayed. The coating will any way works in compression,no problem at all!

Thanks for your replies. I was considering between 95 MXC, metcoloy II and al-Br coatings. Our replies have made the choice easier and possibly to also the cheapest choice!
Regards

Shantanu
Send this user an email Find all posts by this user
Quote this message in a reply
« Next Oldest | Next Newest »
Post Reply 




Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Roller bearing KevGarty 2 761 02-07-2018
09:43 PM
Last Post: demionkrishan
  Crankshaft bearing coating Met.Eng. 0 1,254 11-09-2015
08:23 PM
Last Post: Met.Eng.
  Valve seat coating shantanu 2 2,353 02-19-2015
03:23 AM
Last Post: Axis Machine
  Journal rebuilding shantanu 7 4,540 11-20-2014
11:29 PM
Last Post: loriolo
  Rebuilding with SS 410 HVOF gpdm 2 1,898 05-01-2014
02:08 PM
Last Post: Gordon
  Coating on shrink fit bearing journals shantanu 1 1,774 01-27-2014
07:44 AM
Last Post: Vijay Deshpande
  HVOF SPRAY ON EN31 BEARING STEEL SHAFTS Zanitech 1 2,583 10-18-2013
11:49 AM
Last Post: Stephen Booth
  Roller Bearing coating sal 6 3,846 08-03-2013
10:23 AM
Last Post: loriolo
  Coating on bearing seating area raviswanadha 4 4,271 09-28-2011
01:59 PM
Last Post: djewell

  • View a Printable Version
  • Send this Thread to a Friend
  • Subscribe to this thread


User(s) browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd

    Subscribe in a reader

    Contact Us | Thermal Spray Coatings | Return to Top | Return to Content | Lite (Archive) Mode | RSS Syndication

Powered By MyBB, © 2002-2019 MyBB Group.


© Copyright Gordon England