5pII chromium oxide coating
04-10-2009, 07:06 PM,
#1
5pII chromium oxide coating
Hi Dear
I have 5pII gun and i coated chromium oxide with this.but i have several problems.i done that coating with this parameters:
1-pressure of acetylen 2.5 bar oxygen 2.3bar
2-distance 65 mm
3-Ni-Al band coat
but i don,t know why in one cycle of spraying i get a good deposition but in another one i can not take any deposition without any parameters changing.
is this parameters is best or not?
what is the best parameters for best deposition and coating quality.
i should say that i think when i increase the temp of substrates more than 150 C condition was better but i am not sure.
Reply
04-11-2009, 12:45 PM,
#2
RE: 5pII chromium oxide coating
hi ehsan

Sign0016 to the Surface Engineering Forum.

May I ask which chromium oxide powder product are you using?
Reply
04-12-2009, 04:42 AM,
#3
RE: 5pII chromium oxide coating
Dear Gordon
Thanks for your reply.
I use Cr2O3 powder with -45/+20 size from GTV gmbh(germany company).
Regards
Ehsan
Reply
04-12-2009, 06:38 PM,
#4
Exclamation  RE: 5pII chromium oxide coating
Hi Ehsan

Quote:1-pressure of acetylen 2.5 bar oxygen 2.3bar

Is this correct?

If so, PLEASE STOP! It is not safe and dangerous to run acetylene at this pressure (2.5 bar or 36 psi). 1 bar or 15 psi is all you should need at most.

Your powder will be similar to Metco 106F and I would recommend using the parameters for that from the 5P-II Thermospray Gun Instruction Manual for your gun at least as a starting point. You will need 2PSA air jet assembly and under this section of the manual you will find parameters.

With chromium oxide powders of this type you will be lucky to see a deposit efficiency of 20% so don't expect to see rapid coating build-up.
Reply
04-12-2009, 07:26 PM,
#5
RE: 5pII chromium oxide coating
hi gordon
you said that i need 2PSA compressed air what is the meaning of PSA!!
ok i will chek again with this general manual but i increase the pressure because for chromium oxide i need more temprature for flame.
general parameters is:
acetylen 1.1 bar and oxygen 2.1 is it ok?
Ehsan
Reply
04-12-2009, 11:15 PM,
#6
RE: 5pII chromium oxide coating
Hi Ehsan

(04-12-2009, 07:26 PM)ehsan Wrote: hi gordon
you said that i need 2PSA compressed air what is the meaning of PSA!!
ok i will chek again with this general manual but i increase the pressure because for chromium oxide i need more temprature for flame.
general parameters is:
acetylen 1.1 bar and oxygen 2.1 is it ok?
Ehsan

2PSA is part number of air jet assembly needed. You will need to set cross jets to 50 mm and use spray distance of 65 mm. Run with air pressure of 4.8 bar.

Use acetylene @ 1 bar and oxygen @ 1.7 bar. Refer to manual for other parameters as there are two nozzles that can be used - standard P7B-G and high spray rate P7C-K which use slightly different flows and spray rates.
Reply




Possibly Related Threads…
Thread Author Replies Views Last Post
  Chromium carbide parameters for HVOF JP500 Jaryn 2 596 07-01-2020, 04:27 PM
Last Post: ap-praxair
  oxide cluster in NiCrAl plasma coating Zhiguo 5 5,261 09-26-2018, 04:48 PM
Last Post: bpls670
  Flame spray guns 5P, 5PII, Type N Hector Monjardin 1 2,182 11-17-2016, 10:35 PM
Last Post: mgbaca
  Cr2O3 chromium oxide spray problems by Plasma anne 9 5,871 08-01-2016, 08:15 PM
Last Post: anne
  Laminar oxide in hvof coating Lazha 2 3,406 02-24-2014, 09:41 PM
Last Post: KevinS
  Blistering problem in Chromium Carbide Coating -- Reg sreenuvundela 4 5,327 04-28-2013, 07:14 PM
Last Post: shantanu
  Chromium Carbide crack novakmichal86 4 5,519 03-01-2013, 09:04 AM
Last Post: kschewe
  Oxide stringers in Metco 58NS coating thezombiesprayer 2 4,563 08-13-2012, 09:56 AM
Last Post: thezombiesprayer
  chrome oxide coating failure - 24" dia. steel roll rconnor 3 5,492 07-10-2012, 02:37 PM
Last Post: loriolo
  Aluminum oxide+titanium oxide schumi 11 11,299 04-19-2011, 11:15 PM
Last Post: loriolo
  Coating retention - Molybdenum Oxide Butchless1 1 3,577 11-03-2009, 06:52 PM
Last Post: Gordon
  Chrome Oxide Coating: Free Chrome rayudugirish 2 4,959 10-15-2009, 02:30 AM
Last Post: Gordon
  ZrO2+yttrium oxide TBC Coating Colour joanwang 1 5,697 09-11-2009, 05:24 PM
Last Post: Gordon
Shy Chromium Oxide Coating - Surface Finish Ra values Ian Mc 5 10,576 05-15-2009, 05:17 PM
Last Post: Gordon
  Chrome Oxide Coating Failure M Brecker 6 11,882 03-11-2009, 01:36 PM
Last Post: KevinT



Users browsing this thread: 1 Guest(s)





Surface Engineering Forum Sponsor - Alphatek Hyperformance Coatings Ltd